Steve Miller

Last seen: Today | Active since 2011

Statistics

All

Content Feed

Answered
How to use Simscape Longitudinal Wheel
To specify the initial velocity, typically you need to enable the inertia using a dropdown on the block or attach the inertia se...

en dag ago | 0

Answered
Doesn't my license (university license) have simscape driveline?
You can check this web page to see which licenses are available on your campus: https://www.mathworks.com/academia/tah-supp...

en dag ago | 0

Answered
How to determine the velocities,acceleration for joints and piston for Crank slider mechanism in Matlab code?
This Simscape block represents the same type of mechanism: https://www.mathworks.com/help/simscape/ref/slidercrank.html --...

en dag ago | 0

Answered
I am working on Hydraulic brake system in Simulink. I have rotational motion of the pedal and from that I want translation of the following rod. I tried to use Prismatic joint but it doesn't give the motion I need. What should I do?
I believe you need the Wheel and Axle block or the Rack and Pinion block to convert rotational motion to translational motion. ...

2 dagar ago | 0

Answered
How to define the tire and ground contact for tire enveloping characteristics in Simscape Multibody (to simulate the tire driving over an obstacle)?
Tire enveloping behavior is an advanced physical effect which requires viscoelastic structure in the model of the tire. That is...

2 dagar ago | 0

Answered
How to use Simdriveline to build a Ravigneaux Planetary Gear transmission with the centres of a circle of outer planetary gear， inner planetary gear and small sun gear being not on the same line
Simscape Driveline doesn't actually care where your gears are located, it only cares about the gear ratios. If you can conceive...

2 dagar ago | 0

Answered
How can I add acceleration resistance to a driveline model?
There are many ways to limit the acceleration. The resistances you have already added do that already. I believe you wish to li...

2 dagar ago | 0

Answered
What is the transmission time constant in the Variable Ratio Transmission block of SimDriveline?
The transmission time constant refers to the length of time it takes for the variable ratio transmission to reach steady state a...

2 dagar ago | 0

Answered
band brake simscape simulation. some wrong results happen. why it happen? How could I address it?
Without your model, it is difficult to give a specific answer. Your screenshots do not indicate what the "input" to the system ...

2 dagar ago | 0

Answered
Hydraulic lift model via Simscape tool
Without your model, it is difficult to provide a specific answer. I believe you need to look at product of the ratios for all c...

2 dagar ago | 0

Answered
Help with tire magic formula blocks error in simulink
In your model, you have attempted to connect Simscape Driveline 1G blocks and Simscape Driveline 2G blocks using a physical conn...

2 dagar ago | 0

Answered
Steering angle in simscape driveline ?
Simscape Driveline is intended for longitudinal, vertical, and pitch motion of the vehicle. Lateral dynamics is best covered wi...

3 dagar ago | 0

Answered
Simbody // Simple Quarter of Car
The screenshot below shows the structure you are aiming for with your model (model simple_quarter_car_model.slx is attached). Y...

3 dagar ago | 0

Answered
Modeling of a brake system in Simscape
Your model "now.png" is on the right track. If you connected a control signal to the S port of the valve, you would be able to s...

3 dagar ago | 0

Answered
Simscape Multibody Spline only one Point
From what I see, it should be just fine. Normally, your spline should be nx3, but I also tried entering nx2 and still saw it pl...

3 dagar ago | 0

Answered
How can I transfer Torque from "External Force and Torque" block to simscape component ?
To apply a force in Simscape, use an Ideal Force Source block. The External Force and Torque block is for applying forces to Si...

3 dagar ago | 0

Answered
How to model a simple vehicle in Delft Tyre
Take a look at this submission on the File Exchange: Vehicle Dynamics, 14 DOF Model in Simscape Multibody™ https://www.math...

3 dagar ago | 0

Answered
Can I apply the force model in the radial engine with pneumatic force model with position as input instead?
The example sm_radial_engine.slx has a mechanical connection between the piston head and the chamber where the pressure increase...

3 dagar ago | 0

Answered
Simulink engine RPM becomes zero as soon as throttle increases from 0. I have specified initial rpm to engine which reaches 0 as soon as throttle input to the engine increases from 0?
Without your model, it is very hard to help you. It seems like your engine is stalling, but the information you have provided d...

3 dagar ago | 0

Answered
braking torque calculation of motorcycle drum-shoe brake
This example uses the Double Shoe Brake block to slow down a vehicle: Vehicle with Four-Speed Transmission https://www.math...

3 dagar ago | 0

Answered
Hey guys. I'm doing a project on designing epicyclic gearbox. You are meant to be able to change the ratio and the diameter of the sun gear. The problem is that I can't think of a way to make them always mesh. So any ideas??
You will need to carefully check your radii, gear ratios, initial angles, and number of planets. This can all be related algebr...

3 dagar ago | 0

Answered
Nonlinear solver to advance time one step failed to converge due to Linear Algebra error. Failed to solve using iteration matrix. ...Equations (including nonlinear equations) of one or more components may be dependent or inconsistent. what to do?
Without your model, there is not much we can do to help you. Try commenting out pieces of your model until it works. Then, add...

3 dagar ago | 0

Answered
ABOUT M.TECH PROJECT
See Behavioral model of MEMS accelerometer in Simscape Electrical https://www.mathworks.com/help/sps/ref/accelerometer.html...

3 dagar ago | 0

Answered
Engine maximum speed has exceeded by changing engine and clutch parameters?
You can enable the redline control option in the Generic Engine block - see screenshot below. Test it in Vehicle with Manual Tr...

3 dagar ago | 0

Answered
How to design a model of car in simulink which implies Automatic Emergency Braking in it. and also controls the slip ratio to a value of 0.2?
Take a look at Anti-Lock Braking System (ABS) https://www.mathworks.com/help/hydro/ug/antilock-braking-system-il.html This...

3 dagar ago | 0

Answered
How can I produce plots that mimic the one found in this paper?
Take a look at this example, Double Mass Spring Damper in Simulink and Simscape https://www.mathworks.com/help/simscape/ug/...

3 dagar ago | 0

Answered
IC Engine Simulation, Help with Loops
Take a look at the documentation for this Simscape Driveline block, Generic Engine. https://www.mathworks.com/help/sdl/ref/...

3 dagar ago | 0

Answered
How can i make a Cam and Rolling Follower using Simscape?
In the File Exchange submission Simscape Multibody Contact Forces Library https://www.mathworks.com/matlabcentral/fileexcha...

3 dagar ago | 0

Answered
Simulink Slip Rate Control (ABS Modelling)
Take a look at this example to get started: https://www.mathworks.com/help/hydro/ug/antilock-braking-system-il.html --Steve

3 dagar ago | 0

Answered
Using simDriveline model, no lost ( efficiency 100%) in my driveline model, why the power is reduced
Without your model, it is hard to be sure what the error is. I suspect you haven't properly sensed and calculated the power in ...

3 dagar ago | 0

Steve Miller

Statistics

MATLAB Answers

MATLAB Answers

File Exchange

File Exchange

MATLAB Answers

File Exchange

MATLAB Answers

File Exchange

File Exchange

File Exchange

File Exchange

File Exchange

Content Feed