Statistics
RANK
346
of 300 331
REPUTATION
244
CONTRIBUTIONS
0 Questions
103 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
42
RANK
814 of 20 920
REPUTATION
2 302
AVERAGE RATING
4.50
CONTRIBUTIONS
3 Files
DOWNLOADS
71
ALL TIME DOWNLOADS
20826
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Simulink unable to connect to target with multiple C2000 processors connected via a USB hub
Hi Peter, Very interesting question. It is possible to run multiple instances of Monitor and Tune at the same time, here are c...
3 månader ago | 1
| accepted
How to modify an existing Simulink TI C2000 ePWM block?
Hi Mike, As explained on the following page: https://www.mathworks.com/matlabcentral/answers/1861853-using-a-memory-copy-block...
ungefär 2 år ago | 0
How to write to register for TI DSPs?
Hi Mike, As explained on the following page: https://www.mathworks.com/matlabcentral/answers/1861853-using-a-memory-copy-block...
ungefär 2 år ago | 0
Using a Memory Copy block to read/write a single bit gives an error, and workaround not working?
Hi Mike, A workaround is to use the .all notation to have access to the whole register, you can then use bit manipulations to a...
ungefär 2 år ago | 0
Submitted
Dual Motor Control with TI LAUNCHXL-F28069M LaunchPad
Field-Oriented Control with TI LAUNCHXL-F28069M, BOOSTXL-DRV8301 inverters and 2 PMS motors
ungefär 2 år ago | 12 downloads |
Submitted
Motor Control with TI LaunchPad
Permanent Magnet Synchronous Motor Field-Oriented Control with TI LaunchPad and BOOSTXL-DRV8301
ungefär 2 år ago | 28 downloads |
C2000 TI F2806x PIL simulation is working extremely slow
Hello Aqeel, 1MHz (or 1e-6 second of sample time) is pretty fast for the F28069. The fact that you are observing 2 seconds in s...
mer än 2 år ago | 0
| accepted
Embedded coder with Toshiba Arm core MCU
Hi Ahmed Ahmed, We don't have peripheral support for toshiba processors. The best way to work with these processors is to gene...
mer än 3 år ago | 0
| accepted
c2000_DCDC_Buck_host_model.slx not found for DC/DC Buck converter example F28379
Hi Hal Der, The link you are using for the documentation doesn't specify the MATLAB release you are using and always points to ...
mer än 3 år ago | 0
Embedded coder for TI C2000 WITHOUT external mode
The easiest is just to press Ctrl+B on your model instead of pressing the play button. Depending on which version of MATLAB you...
ungefär 4 år ago | 0
C2000 CLA _DWork Variable Problem
Hi Keith, The solution to your problem is explained on this page: https://www.mathworks.com/help/releases/R2021a/supportpkg/te...
ungefär 4 år ago | 0
| accepted
Looking for a F28379D controller internal system reset command via Simulink
My gut feeling tells me that this could be a problem related to float math losing resolution as the time increases. Few points:...
ungefär 5 år ago | 0
Serial communication between two Launchpads
There are multiple ways you can do this. The simplest that comes to my mind would be to use SCI. Just connect the Tx pin of one ...
mer än 5 år ago | 1
Programing C2000 F28069M using Matlab simulink
Hi Damsith Wasala, This is a logging issue. Your ADC is fine, External mode is not able to log at these rates. Please take a l...
nästan 6 år ago | 1
memory simulink c2000
Hi Juan, Look at the section "Data Logging" on the following page. You can set triggers on when to to record and when to stop ...
nästan 6 år ago | 1
| accepted
Modbus RTU Slave TI C2000
Hi Francisco, We don't have out-of-the-box support for Modbus. I think that you could implement it on your own, either with ou...
ungefär 6 år ago | 0
| accepted
F28335 Timer1 & Timer2 Construction - Using via Simulink
To add to Venkatesh's response: You can use regular sample times in your Simulink model to achieve 3 tasks of 100Hz, 1kHz and 1...
mer än 6 år ago | 0
| accepted
Which hardware board should I use for DRV8312?
Hi Karol, For the F2806x ControlCard, the F2806x will have better default compared to the F28069M LaunchPad. Things to keep in...
mer än 6 år ago | 0
| accepted
C2000 Embedded Coder: Does Simulink flash the OTP?
Hi Offroad, Standalone execution is our default boot for the F28069M LaunchPad. Make sure that you have the LaunchPad board sel...
mer än 6 år ago | 0
Real-time simulation with C2000 device
Hi Eduard, PIL is not meant to be realtime. The primary use case for PIL is verification of the results produced by the generat...
mer än 6 år ago | 0
TI C2000 code generation generates double data type functions instead of single ones
Hi Gergely, On C2000 devices, double maps to single. I don't think there is any difference between sinf and sin. The result and...
mer än 6 år ago | 1
| accepted
Reset eCAP value when the input signal off
Hi Eduard, It's surprising that the memory copy block returns the same value. Please double check the settings like data types ...
mer än 6 år ago | 0
| accepted
Reset eCAP value when the input signal off
Hi Eduard, Interesting question. The capture module can only give you time that elapsed between edges. If your PWM reaches 0% o...
mer än 6 år ago | 0
The created PIL block links automatically to COM5
Hi Eduard, The COM settings you are referring to on the configuration parameters propably belong to External mode and not PIL. ...
mer än 6 år ago | 0
| accepted
Error in using ePWM (TI F28027 LaunchPad) - Error evaluating 'InitFcn' callback of C280x/C2833x ePWM block (mask) 'untitled/ePWM'.
Hi Deep, Pick your PWM block from the C2802x library. The one you are using right now is for a different family of processors....
mer än 6 år ago | 0
| accepted
TMS320F28335: Model for Simulink based buck converter control
Hi Priyanka, Are you trying to run "Peak current control"? Let us know, Thanks, Antonin.
mer än 6 år ago | 0
Embedded coder generated code run on TI C2000 F28335 Ram well but not run on Flash
Hi Ömer, Are you using different controlCards from TI? Depending on the controlCard that you use, TI has placed crystals of di...
mer än 6 år ago | 0
| accepted
Problem in Data Type Conversion - ti C2000 DC/DC Buck Converter example
Hi Saeed Heshmatian, Welcome to the world of Fixed-Point! In many of our examples, we like to keep our units between -1 and 1 ...
nästan 7 år ago | 3
| accepted
Problem in programming 28379D from Simulink
I would start by removing the 14 exclamation marks in the folder name. It looks like the flashing tool doesn't like these.
nästan 7 år ago | 0
eCAN loading problems to TI C2000 C28x3x card; are example only for Vector hardware
Hi Mike, Our CAN solution is based on the Vector XL Library which is compatible with pretty much all Vector hardware. We teste...
nästan 7 år ago | 0
