Pack individual signals into CAN message
Embedded Coder®/ Embedded Targets/ Host Communication
The CAN Pack block loads signal data into a message at specified intervals during the simulation.
To use this block, you also need a license for Simulink® software.
CAN Pack block has one input port by default. The number of block inputs is dynamic and depends on the number of signals you specify for the block. For example, if your block has four signals, it has four block inputs.
This block has one output port, CAN Msg. The CAN Pack block takes the specified input parameters and packs the signals into a message.
The CAN Pack block supports:
The use of Simulink Accelerator™ Rapid Accelerator mode. Using this feature, you can speed up the execution of Simulink models.
The use of model referencing. Using this feature, your model can include other Simulink models as modular components.
Code generation to deploy models to targets.
Code generation is not supported if your signal information consists of signed or unsigned integers greater than 32 bits long.
For more information on these features, see the Simulink documentation.
Use the Function Block Parameters dialog box to select your CAN Pack block parameters.
Select your data signal:
raw data: Input data as a uint8 vector array. If you select this option, you only specify the message fields. all other signal parameter fields are unavailable. This option opens only one input port on your block.
manually specified signals: Allows you to specify data signal definitions. If you select this option, use the Signals table to create your signals. The number of block inputs depends on the number of signals you specify.
CANdb specified signals: Allows you to specify a CAN database file that contains message and signal definitions. If you select this option, select a CANdb file. The number of block inputs depends on the number of signals specified in the CANdb file for the selected message.
The block supports the following input signals data types: single, double, int8, int16, int32, int64, uint8, uint16, uint32, uint64, and boolean. The block does not support fixed-point data types.
This option is available if you specify that your data is input via a CANdb file in the Data is input as list. Click Browse to find the CANdb file on your system. The message list specified in the CANdb file populates the Message section of the dialog box. The CANdb file also populates the Signals table for the selected message.
File names that contain non-alphanumeric characters such as equal signs, ampersands, and so forth are not valid CAN database file names. You can use periods in your database name. Rename CAN database files with non-alphanumeric characters before you use them.
This option is available if you specify that your data is input via a CANdb file in the Data is input as field and you select a CANdb file in the CANdb file field. Select the message to display signal details in the Signals table.
Specify a name for your CAN message. The default is
Msg. This option is available if you choose to input raw
data or manually specify signals. This option in unavailable if you
choose to use signals from a CANdb file.
Specify whether your CAN message identifier is a
Standard or an
The default is
Standard. A standard identifier is an
11-bit identifier and an extended identifier is a 29-bit identifier.
This option is available if you choose to input raw data or manually
specify signals. For
CANdb specified signals, the
Identifier type inherits the type from the
Specify your CAN message ID. This number must be a positive integer
from 0 through 2047 for a standard identifier and from 0 through
536870911 for an extended identifier. You can also specify hexadecimal
values using the
hex2dec function. This
option is available if you choose to input raw data or manually specify
Specify the length of your CAN message from 0 to 8 bytes. If you are
CANdb specified signals for your data input,
the CANdb file defines the length of your message. If not, this field
8. This option is available if you choose
to input raw data or manually specify signals.
Specify the CAN message as a remote frame.
Select this option for the block to output CAN messages as a Simulink bus signal. For more information on Simulink bus objects, see Composite Signals (Simulink).
This table appears if you choose to specify signals manually or define signals using a CANdb file.
If you are using a CANdb file, the data in the file populates this table automatically and you cannot edit the fields. To edit signal information, switch to manually specified signals.
If you have selected to specify signals manually, create your signals manually in this table. Each signal you create has the following values:
Specify a descriptive name for your signal. The Simulink block in your model displays this name. The default is
Signal [row number].
Specify the start bit of the data. The start bit is the least significant bit counted from the start of the message data. The start bit must be an integer from 0 through 63.
Specify the number of bits the signal occupies in the message. The length must be an integer from 1 through 64.
Select either of the following options:
LE: Where the byte order is in
little-endian format (Intel®). In this format you count bits from the start,
which is the least significant bit, to the most significant bit,
which has the highest bit index. For example, if you pack one
byte of data in little-endian format, with the start bit at 20,
the data bit table resembles this figure.
Little-Endian Byte Order Counted from the Least Significant Bit to the Highest Address
BE: Where byte order is in big-endian
format (Motorola®). In this format you count bits from the start,
which is the least significant bit, to the most significant bit.
For example, if you pack one byte of data in big-endian format,
with the start bit at 20, the data bit table resembles this
Big-Endian Byte Order Counted from the Least Significant Bit to the Lowest Address
Specify how the signal interprets the data in the allocated bits. Choose from:
Specify how the block packs the signals into the CAN message at each timestep:
signal is packed at each timestep.
Multiplexor signal, or the mode
signal is packed. You can specify only one
Multiplexor signal per
Multiplexed: The signal is packed
if the value of the
signal (mode signal) at run time matches the configured
Multiplex value of this signal.
For example, a message has four signals with the following types and values.
|Signal Name||Multiplex Type||Multiplex Value|
In this example:
The block packs Signal-A (Standard signal) and Signal-D (Multiplexor signal) in every timestep.
If the value of Signal-D is 1 at a particular timestep, then the block packs Signal-B along with Signal-A and Signal-D in that timestep.
If the value of Signal-D is 0 at a particular timestep, then the block packs Signal-C along with Signal-A and Signal-D in that timestep.
If the value of Signal-D is not 1 or 0, the block does not pack either of the Multiplexed signals in that timestep.
This option is available only if you have selected the
Multiplex type to be
Multiplexed. The value you provide here must
Multiplexor signal value at run
time for the block to pack the
signal. The Multiplex value must be a positive
integer or zero.
Specify the Factor value to apply to convert the physical value (signal value) to the raw value packed in the message. See Conversion Formula to understand how physical values are converted to raw values packed into a message.
Specify the Offset value to apply to convert the physical value (signal value) to the raw value packed in the message. See Conversion Formula to understand how physical values are converted to raw values packed into a message.
Define a range of signal values. The default settings are
-Inf (negative infinity) and
Inf, respectively. For CANdb specified
signals, these settings are read from the CAN database.
For manually specified signals, you can specify the
minimum and maximum physical value of the signal. By default, these
settings do not clip signal values that exceed them.
The conversion formula is
raw_value = (physical_value - Offset) / Factor
physical_valueis the original value of the signal, and
raw_valueis the packed signal value.