Community Profile

photo

Craig Cowled


Queensland University of Technology

Last seen: 9 dagar ago |  Active since 2011

Followers: 0   Following: 0

Message

Statistics

  • First Review
  • 3 Month Streak
  • Thankful Level 3
  • Knowledgeable Level 2
  • First Answer

View badges

Feeds

View by

Question


importfile regexp thousands separator returns NaN when negative
I used "Import Data" to generate a function importfile for importing a csv file. Unfortunately, the function returns NaN for ev...

nästan 5 år ago | 1 answer | 0

1

answer

Answered
Is it possible to make a manual Nyquist plot using polar(theta,rho)
Jeffrey, I usually keep my data in one complex vector rather than having two vectors (i.e., mag & phase). Then it's a simple th...

nästan 11 år ago | 0

Question


how to pass multiple values of x to objective function in GA / Patternsearch
I'm looking for ways to speed up the computation of my optimisation process. I've already used the PROFILE command to pinpoint ...

nästan 11 år ago | 1 answer | 0

1

answer

Answered
Genetic Algorithm options 'PopInitRange' not working
Alan, thank you for such a good explanation. Cleared it up for me nicely.

nästan 11 år ago | 0

Question


Genetic Algorithm options 'PopInitRange' not working
I am using GAOPTIMSET to establish an upper and lower bound for my initial population in a GA optimisation. I have abbreviate...

nästan 11 år ago | 2 answers | 0

2

answers

Answered
How do you share a variable from another function to be used in a different function?
Cordelle, I'm not going to re-write your code for you, but I will suggest that you read up on nested functions, here ... ht...

nästan 11 år ago | 0

| accepted

Answered
power spectrum VS amplitude of FFT function
Power = 20 * log10(abs(FFT))

nästan 11 år ago | 0

Answered
Restarting Genetic Algorithm after Crash
Many thanks yet again, Alan. Will write a little function to handle the crash and restart the GA. As for patternsearch, I mi...

nästan 11 år ago | 0

Answered
Matlab crashes when calling dll
Try using 'loadlibrary'.

nästan 11 år ago | 0

Question


Restarting Genetic Algorithm after Crash
I'm using the GA to update my Finite Element Model. The fitness function I am using is computationally expensive and takes 4sec...

nästan 11 år ago | 2 answers | 0

2

answers

Answered
Use of PSD functions to obtain FRFs
I thought I should tie up a loose end with this question. I discovered that the data acquisition from my impact hammer was faul...

nästan 11 år ago | 1

Answered
Curve fitting a complex function using cftool
MattJ, not sceptical ... always worthwhile to know the intrinsic quirks of an algorithm. I used your code and compared the di...

nästan 11 år ago | 0

Answered
Curve fitting problem and strange message
Fei, if the "change in residuals is less than tolerance" then this is an indication that you have a reasonably good fit. I ha...

nästan 11 år ago | 0

Answered
genetic algorithm error not enough input arguments
Hey, what do you know, it worked!! Btw, your recommendation of using LSQNONLIN was the right call too. Although the GA wor...

nästan 11 år ago | 0

Answered
genetic algorithm error not enough input arguments
Alan, Thank you for taking the time to answer this in so much detail! Point taken regarding the choice of optimization too...

nästan 11 år ago | 0

Question


genetic algorithm error not enough input arguments
function deltaH = curvefit_H_2modes(w1,w2,m1,m2,c1,c2) load('file.mat'); z = -(x.^2) .* ((1 ./ ((w1.^2 * m1) -...

nästan 11 år ago | 4 answers | 0

4

answers

Answered
How to Fix this Error!
Send this to Matlab Support. Obviously their help file has the wrong code.

nästan 11 år ago | 0

Answered
RMS question plss help me
Mohd, if you have the Signal Processing Toolbox, you can use the _rms_ function like this: X = [0.234 0.2338 0.255 3.456 5....

nästan 11 år ago | 0

Answered
Curve fitting a complex function using cftool
I just noticed another question on the forum in which someone suggested to use _mldivide_. I'll have a look at this when I get ...

nästan 11 år ago | 0

Answered
how to acces and change value inside transfer function inside a loop
Kobi, I tried running your code and got an error message. It looks like you missed a space between G.den{1,1} and (k) in the li...

ungefär 11 år ago | 0

| accepted

Answered
pseudorandomise vectors in an array
Doug, I use a function that was developed by Jos, called _allcomb_. You can find it at the following link <http://www.mathworks...

ungefär 11 år ago | 0

| accepted

Answered
How can I generate random numbers with constraints?
I think you have actually answered your own question. If x = randi([3 18], 7); gives you a 7 x 7 matrix of random numbers betwe...

ungefär 11 år ago | 0

Question


bar3 width depend on zdata?
Ok, so I know how to make the colours on my bar graph depend on zdata .. h = bar3(data); for ii = 1:length(h) zdata =...

ungefär 11 år ago | 0 answers | 0

0

answers

Answered
Boxplot with time on x axis
Found the answer ... Need to use 'positions' like this boxplot(Y,'positions',X)

ungefär 11 år ago | 4

| accepted

Answered
Excel Date Format to Matlab Number Array
Have you tried using datevec? Take one of the cells as an example ... '02/03/2013'. >> datevec('02/03/2013','mm/dd/yyyy')...

ungefär 11 år ago | 0

| accepted

Question


Boxplot with time on x axis
Does anybody know how to obtain a boxplot with time on the x axis? I have collected experimental observations at irregular in...

ungefär 11 år ago | 1 answer | 1

1

answer

Question


Curve fitting a complex function using cftool
I'm using the cftool toolbox to find fits for a complex valued transfer function. The toolbox clearly can't handle a complex nu...

ungefär 11 år ago | 3 answers | 0

3

answers

Question


Use of PSD functions to obtain FRFs
Hi, I am doing some modal analysis on a steel structure and have encountered some troubling issues while using Matlab's Power...

mer än 12 år ago | 2 answers | 1

2

answers