Statistics
RANK
90 780
of 300 338
REPUTATION
0
CONTRIBUTIONS
12 Questions
2 Answers
ANSWER ACCEPTANCE
8.33%
VOTES RECEIVED
1
RANK
of 20 922
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANK
of 168 124
CONTRIBUTIONS
0 Problems
0 Solutions
SCORE
0
NUMBER OF BADGES
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Question
How do I use Simulink Coder to build a Simulink model and generate the necessary header files that seem to be missing?
Hello, I’m trying to build a simple LQR block diagram using Simulink Coder for deployment on a Raspberry Pi board. However, du...
3 månader ago | 1 answer | 0
1
answerQuestion
How to implement an LQR controller when the system's state variables and control inputs have different units?
Hello, I am wondering how to implement an LQR controller when the state variables and control inputs have different units. For...
9 månader ago | 1 answer | 0
1
answerQuestion
How to implement MPC when the number of states is greater than the number of outputs?
I want to implement MPC using MATLAB's Model Predictive Control Toolbox. When I checked the official MATLAB website, I found on...
9 månader ago | 1 answer | 0
1
answerHow to troubleshoot pixhawk build error problem during executing example file?
Hello, I have another problem, that is QGroundControl doesn't recognize a pixhawk board when px4 firmware was built from MATL...
9 månader ago | 0
How to troubleshoot pixhawk build error problem during executing example file?
I just fixed this problem by installing PX4-Autopilot firmware to the Linux home directory(not windows directory) and not execut...
9 månader ago | 1
Question
How to troubleshoot pixhawk build error problem during executing example file?
Hello, I want to execute the example of Send and Receive Serial Data Using PX4 Autopilots Support Package. I followed the step...
9 månader ago | 2 answers | 0
2
answersQuestion
How can I execute a Simulink block only when a specific condition is met?
Hi all, Is there a way to execute the following block diagram only when a certain condition is satisfied (e.g., when a joysti...
12 månader ago | 1 answer | 0
1
answerQuestion
How to use "StabilityThreshold" estimation option in greyest function?
Hello, To predict the lateral equations of the H4 Hercules using a greybox model, I defined the model function as follows and s...
ungefär ett år ago | 1 answer | 0
1
answerQuestion
Problem Occurred While Using MATLAB System Identification Toolbox
Hello, I am currently performing system identification using the System Identification Toolbox after extracting the response dat...
ungefär ett år ago | 1 answer | 0
1
answerQuestion
Inquiry about IP address and port number for UDP Send and UDP Receive block
Hello all, I have a question about the IP addresses and port numbers for the UDP Send and UDP Receive blocks. When sending and ...
ungefär ett år ago | 1 answer | 0
1
answerQuestion
How to store object(like udp object) in level-2 s-function?
Hello all, I want to send control input from Matlab to FlightGear and receive aircraft data from FlightGear to Matlab with UDP ...
ungefär ett år ago | 1 answer | 0
1
answerQuestion
How to calculate minimum singular value of I+L and I+inv(L) for MIMO system?
Hello, I want to calculate minimum singular value for MIMO system, and here is an example %% A = [0.1873 0.8403 -0.6003 -2.1...
mer än ett år ago | 1 answer | 0
1
answerQuestion
What's the difference between two command?
Hello, In general, the command of nyquist plot is nyquist(sys,omega), but an example of textbook the command of nyquist is nyqu...
mer än ett år ago | 1 answer | 0
1
answerQuestion
How to maintain eigenvalues sequence
Hello, I have to draw root-locus for longitudinal motion; Short Period Mode and Phugoid Mode. Here is a code %% Dynamics Vp =...
nästan 2 år ago | 0 answers | 0
