![photo](/responsive_image/150/150/0/0/0/cache/matlabcentral/profiles/17501832_1581375011016_DEF.jpg)
saleh shlimet
Followers: 0 Following: 0
Statistics
13 Questions
0 Answers
RANK
244 134
of 293 477
REPUTATION
0
CONTRIBUTIONS
13 Questions
0 Answers
ANSWER ACCEPTANCE
30.77%
VOTES RECEIVED
0
RANK
of 20 033
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANK
of 148 733
CONTRIBUTIONS
0 Problems
0 Solutions
SCORE
0
NUMBER OF BADGES
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Question
How can I obtain the difference between two data stored in workspace?
I experimentally tested a motor and the measured speed and the reference speed were stored in the workspace. My supervisor aske...
9 månader ago | 1 answer | 0
1
answerQuestion
How to execute the same code for a specific time?
I want to estimate the shaft speed of a motor and to do that I obtain the speed error between the reference speed and the estima...
mer än ett år ago | 1 answer | 0
1
answerQuestion
Position error of motor shaft
I want to obtain the position error of motor shaft so I subtracted the estimated position from the measured position. modulus f...
mer än ett år ago | 1 answer | 0
1
answerQuestion
how to export varied variable to saturation block in Simulink?
I tried to use varied value in the Saturation block and this value (called flux) exported from the output of a lookup table? I u...
mer än ett år ago | 1 answer | 0
1
answerQuestion
Use a command only once
I use a code to search for an accurate rotor position. I used an initial value for the position (theta_b=0) as shown below and t...
nästan 2 år ago | 2 answers | 0
2
answersQuestion
Code error in MATLAB function block.
I wrote a code in a MATLAB function block that consists of two inputs one input for the signal that needs to be filtered and the...
mer än 2 år ago | 1 answer | 0
1
answerQuestion
Calculate cycle time for a signal by code
I want to calculate the cycle time for a signal (the frequency) by using a code (Matlab function block). For examble, in a motor...
mer än 2 år ago | 0 answers | 0
0
answersQuestion
Why the amplitude of the 90 shifted phase signal when use the analytic signal block is not equal to the original signal?
I could manage to shift the phase of signal by 90 by using analytic signal block. But, the problem is that its amplitude is not ...
ungefär 4 år ago | 1 answer | 0
1
answerQuestion
how to shift phase of unknown frequency signal by 90 by using hilbert transform?
I tried to shift an unknown frequency signal by 90 by applying hilbert transform comand (imag(hilbert(x)) in matlab function blo...
ungefär 4 år ago | 0 answers | 0
0
answersQuestion
How to connect simulink blocks with RF blocks (interface)?
I tried to use simulink blocks with RF blocksets but they can not be connected to each other. I think there is an interface betw...
ungefär 4 år ago | 1 answer | 0
1
answerQuestion
How to shift a signal in simulink by 90 degrees?
I want to shift a signal by 90 degrees. there is a block called phase shift in RF blockset, but it cannot be used with simulink....
ungefär 4 år ago | 1 answer | 0
1
answerQuestion
A problem with the solver
A problem with the solver when I run a model. when I disconnect the gate driver (simulink) from the inverter (simcap) the proble...
mer än 4 år ago | 1 answer | 0
1
answerQuestion
measuring the phase to neutral voltage in PMSM
in the MATLAB, how can I measure the voltage between the phase and the neutral point in the PMSM machine? (there is no access to...
mer än 4 år ago | 1 answer | 0