Ardeal Liang
Followers: 0 Following: 0
Statistics
RANK
268 474
of 293 471
REPUTATION
0
CONTRIBUTIONS
8 Questions
4 Answers
ANSWER ACCEPTANCE
50.0%
VOTES RECEIVED
0
RANK
of 20 032
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANK
of 148 733
CONTRIBUTIONS
0 Problems
0 Solutions
SCORE
0
NUMBER OF BADGES
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Highlights
AVERAGE NO. OF LIKES
Feeds
Question
Recevied signal from ARM is not correct
Hi, I have zedboard and AD9364. I am trying to reproduce the Matlab example in ARM in C code: Receive Tone Signal Using Ana...
nästan 6 år ago | 0 answers | 0
0
answersQuestion
Set the source of transmitter to be DDS on zedboard and AD3964
Hi, I have the boards: AD-FMCOMMS4-EBZ(which is AD9364) and Zedboard I am going to try the experiment of Matlab in C ...
nästan 6 år ago | 0 answers | 0
0
answersQuestion
The specified superclass 'comm.internal.SDRTxZynqFMC234Base' contains a parse error, cannot be found on MATLAB's search path, or is shadowed by another file with the same name
Hi Paul, I am trying to package the example code as an individual app via Matlab menu: APPS-->APPLICATION DEPLOYMENT --> A...
nästan 6 år ago | 0 answers | 0
0
answersQuestion
How to control GPIO of ARM on Zedboard
Hi Paul, I would like to control the GPIO of ARM on my Zedboard. I would like to set one/some GPIO to be 1 or 0. Which ...
nästan 6 år ago | 1 answer | 0
1
answerChang center frequency quickly
Hi Paul, Thanks for your answer! Here are the steps(pseudo-code) of the exeriment I wang to do: for rf_scan = 1:10 ...
nästan 6 år ago | 0
Chang center frequency quickly
Hi Paul, At present, the example runs on Matlab, and send commands to ARM to talk to AD9364 by RJ45 interface. So, the exa...
nästan 6 år ago | 0
| accepted
Question
Chang center frequency quickly
Hi Paul, I would like to change center frequency quickly. If I change it and then restart the object in Matlab, it runs too ...
nästan 6 år ago | 3 answers | 0
3
answersQuestion
The received signal from sdrrx keeps unchanged even if I connect or disconnect the loopback cable to trainsmitter port TxA and receiver port RxA
Hi, I am trying to reproduce this example: Receive Tone Signal Using Analog Devices AD9361/AD9364from: https://ww2.mathwor...
nästan 6 år ago | 1 answer | 0
1
answerQuestion about how to run TX and RX calibration example model on zedboard with zynq
Hi Paul, Many thanks for your answer! according to your answer, I should not run tx and rx on one board. However, I cannot u...
nästan 6 år ago | 0
Question
Run transmitter and receiver model in 1 model or 2 separate model in parallel
I have only 1 set of the hardware boards(AD-FMCOMMS4-EBZ(which is AD9364) and Zedboard). so I will run both transmitter and re...
nästan 6 år ago | 1 answer | 0
1
answerQuestion about how to run TX and RX calibration example model on zedboard with zynq
In the Matlab help link: https://ww2.mathworks.cn/help/supportpkg/xilinxzynqbasedradio/examples/frequency-offset-calibratio...
nästan 6 år ago | 0
Question
Question about how to run TX and RX calibration example model on zedboard with zynq
I am doing an experiment: I combined the following two examples: Transmitter example: https://ww2.mathworks.cn/help/support...
nästan 6 år ago | 3 answers | 0