Community Profile

photo

Gayatri Menon

Last seen: Today Active since 2017

Statistics

All
  • Knowledgeable Level 3
  • Revival Level 3
  • First Review
  • Solver
  • 3 Month Streak
  • Knowledgeable Level 2
  • First Answer

View badges

Content Feed

View by

Answered
Connect to a ADXL335
Hi Assuming one of the analog output pin on the sensor is connected to A4 on Arduino . Now voltage read needs to be converted ...

7 månader ago | 0

Answered
bno055 System "uncalibrated"
Hi Have you tried the calibration steps as mentioned in the below doc https://in.mathworks.com/help/supportpkg/arduinoio/ug/...

7 månader ago | 0

Answered
Arduino/BNO055 example code not working, "Command logs are not supported for sensors. Create the hardware Object with property 'TraceOn' disabled." error.
Hi, Trace is not supported for read(imu) . Create the arduino object with 'TraceOn' set as false and then try the rest of the ...

7 månader ago | 0

Answered
How to see BNO055 outputs in Simulink ?
Hi, Consider using BNO055 block in Simulink to read data from sensor. To view the data read from sensor, consider using 'Conne...

7 månader ago | 0

Answered
Using I2C with arduino For accelerometer
Hi, Consider using BNO055 block to read data from sensor connected to arduino Thanks Gayatri

7 månader ago | 0

Answered
Simulink - Arduino to read out sparkfun 9dof IMU returns zero
Hey LSM9DS1 block in Simulink can be used to read the data from LSM9DS1 sensor Please see the link for more info LSM9DS1 bl...

7 månader ago | 0

Answered
Reading sensor data off a ICM-20948 via i2c with Arduino uno
Hi, Even though ICM20948 is the recommended sensor over MPU9250, the register settings for both the sensors are different. Hen...

7 månader ago | 0

| accepted

Answered
How to Calibrate MPU6050 sensor using MATLAB?
Hi, The below link contains an example of using Complementary filter with MPU-9250 sensor Estimate Orientation with a Complem...

7 månader ago | 0

| accepted

Answered
MPU 6050 and Raspberry pi
Hi, Use mpu6050() to do this. Refer this link for more info. mypi = raspi; sensor = mpu6050(mypi,'Bus','i2c-1'); sensor.re...

8 månader ago | 0

Answered
Need help with plotting accelerometer readings from MPU6050 + Arduino.
Please refer to the answer to ML Answer Plotting mpu6050 data Hope this helps Thanks Gayatri

9 månader ago | 0

Answered
Need help with an example to plot data in real-time from (MPU6050) using Arduino to MATLAB
Refer the follow ML Answer Thanks Gayatri

9 månader ago | 0

Answered
Plotting output of three MPU6050 sensors in Matlap in three different graphes
Hi, For Arduino board, you could use mpu6050() to connect MPU6050 sensor a = arduino; imu = mpu6050(a); xlabel('Count'); y...

9 månader ago | 0

Answered
Need help with plotting accelerometer readings from MPU6050 + Arduino.
Hi, For Arduino board, you could use mpu6050() to connect MPU6050 sensor MPU6050 - Arduino a = arduino; imu = mpu6050(a); ...

9 månader ago | 0

Answered
multiple mpu6050 with S function
Hi, You can connect to MPU6050 on Arduino using MPU6050 block . To connect 2 MPU6050s on the same Arduino I2C bus by changing...

9 månader ago | 0

Answered
Undefined function or variable 'I2Cdev'.
The below link might help you in interfacing mpu6050 connected to arduino: https://www.mathworks.com/help/supportpkg/arduinoio/...

9 månader ago | 0

Answered
How to connect multi MPU6050 to matlab?
Hi, If you are using Arduino or RaspberryPi board, you could use mpu6050() to connect MPU6050 sensor MPU6050 - Arduino MPU60...

9 månader ago | 0

Answered
Multi MPU6050 matlab code
Hi, If you are using Arduino or RaspberryPi board, you could use mpu6050() to connect MPU6050 sensor MPU6050 - Arduino MPU60...

9 månader ago | 0

Answered
GPS interface
Hi, This example might be helpful for you https://in.mathworks.com/help/nav/ug/plot-position-using-nmea-example.html Thanks...

9 månader ago | 0

Answered
I want use a gps in matlab
Hi, nmeaParser() in Navigation toolbox can be used to parse data from GPS. Serial connection can be established using serialpo...

9 månader ago | 0

Answered
GPS interface
Hi, nmeaParser() in Navigation toolbox can be used to parse data from GPS. Serial connection can be established using serialpo...

9 månader ago | 0

Answered
Matlab and GPS
Hi, nmeaParser in Navigation toolbox can be used to parse data from GPS. Refer the following links for more info : https://in...

9 månader ago | 0

Answered
Serial communication with a header and a terminator
Hi, Protocol Decoder block and Protocol Encoder block might be useful in such scenarios. For more info, refer the following ...

9 månader ago | 0

Answered
How to test MPU6050 with arduino Uno in simulink?
Hi, Use MPU6050 block to read data from the sensor connected to Arduino in Simulink Thanks Gayatri

9 månader ago | 0

Answered
MPU6050 Arduino Uno Simulink
Hi You could use MPU6050 block in simulink to read data from MPU6050 sensor connected to Arduino. To use MATLAB function block...

9 månader ago | 1

Answered
Using multiple "Serial" ports of arduino mega 2560
Hi, In MATLAB, use device() to connect to serial device on Arduino arduinoObj = arduino("COM16","Leonardo","Libraries",{'SP...

9 månader ago | 1

| accepted

Answered
Two Arduino Uno with 4 MPU6050 IMUs simulink
Hi, You can connect 2 MPU6050s on the same Arduino I2C bus by changing the I2C Address of one of the sensor. This can be don...

9 månader ago | 0

Answered
Mpu9250 calibration with simulink by MATLAB function
Hi magcal function can be used to calibrate magnetometer data. Fusion filters can be used to determine orientation. The below ...

9 månader ago | 0

Answered
Read data from Arduino Nano 33 IoT IMU sensor
Hi, Connecting to LSM6DS3 sensor on Arduino hardware I2C bus can be done by following Use lsm6ds3 object in MATLAB Use LSM6D...

9 månader ago | 0

Answered
Raspberry and MATLAB with MPU9250
Hi, Connecting to MPU-9250 sensor on Raspberry Pi hardware in MATLAB can be done using mpu9250 object. This feature is support...

9 månader ago | 0

Answered
Read and Parse NMEA Data Directly From GPS Receiver-No example
Hi, nmeaParser in Navigation toolbox can be used to parse sentences compliant with NMEA 0183 Standard, Version 4.10. It suppor...

ungefär ett år ago | 0

Load more