You can use Connected I/O to communicate with the IO peripherals on the hardware during Normal mode simulation.
Normal mode simulation with Connected I/O is an intermediate step in the Model-Based Design workflow that bridges the gap between simulation and code generation by enabling Simulink® to communicate with the hardware before deploying the model on the hardware. Connected I/O enables you to modify your model design and monitor the effect of the modified design using the peripheral data from the hardware in a near real-time environment. You are not required to deploy the model on the hardware to monitor the effect of the modified design, which accelerates the simulation process. This Simulink (software)-Arduino® (hardware) interaction is available in Normal mode simulation only when you enable Connected I/O.
These sections explain:
The Connected I/O described here applies to the Simulink Support Package for Arduino Hardware on these Arduino boards and blocks:
Source blocks: Without Connected I/O, these source blocks output zero during Normal mode simulation. With Connected I/O, these blocks read data from the peripherals of the hardware during Normal mode simulation.
Sink blocks: Without Connected I/O, these sink blocks do not have any role during Normal mode simulation. With Connected I/O, these blocks write data to the peripherals of the hardware during Normal mode simulation.
|Arduino Boards||Source Blocks||Sink Blocks|
Arduino MKR WIFI 1010
Arduino MKR ZERO
Arduino Mega 2560
Arduino Nano 3.0
Arduino Nano 33 IoT
Connected I/O creates a communication interface that enables the Simulink model and the IO Server to communicate with each other. The Simulink model resides in your computer, and the IO Server is an engine on the hardware that contains all the peripheral functions. The transport layer formats and transmits the data using the communication interface.
This diagram shows the connection that the Connected I/O creates between your computer and the hardware.
Communication in Normal Mode Simulation with Connected I/O
When you simulate a Simulink model in Normal mode with Connected I/O:
The device driver blocks (for example, Digital Input and Digital Output blocks) in the model request peripheral data from the IO Server.
The IO Server accepts the request and responds with the requested data. You can use any Simulink sink or dashboard block to view the received data. Using the peripheral data received, you can verify that your model design meets the requirements.
If necessary, you can modify the design by adding, removing, or replacing any block in the Simulink model.
After the model is modified, resimulate the model. During simulation, the data request from the model is communicated to the hardware. You can continue to modify and simulate the model until the expected behavior is achieved.
The communication in Connected I/O is an on-demand process. The hardware sends data only when receiving a data request from the Simulink model.
You do not have to build, deploy, and run the model on the hardware to monitor the effects of your changes in your model design.
When you simulate a model in Normal mode without Connected I/O, Simulink does not communicate with the hardware. Simulink communicates with the hardware only when the code is generated and the model is deployed on the hardware in External mode. Normal mode simulation with Connected I/O is an intermediate step in the model-based design workflow that bridges the gap between simulation and code generation by enabling Simulink to communicate with the hardware before deploying the model on the hardware.
This Model-Based Design Workflow diagram displays a model-based workflow:
Create a Simulink model.
Simulate the model in:
Normal mode simulation without Connected I/O: There is no hardware interaction and no code generation.
Normal mode simulation with Connected I/O: The model communicates with the hardware. There is no code generation.
External mode: The model is deployed on the hardware and generates code.
Analog input reference voltage parameter is not supported in Connected I/O.
Deploy the model to the hardware.
Model-Based Design Workflow
Connected I/O and External mode both enable you to communicate with the hardware during simulation. However, you use Connected I/O and External mode for different purposes. The table shows the actions that you can perform with each mode.
|Action||External Mode||Connected I/O|
|Obtain real-time data||You can obtain real-time data with External mode.||Enable the Simulink Pacing Option (Simulink) to get near real-time data.|
|Timing analysis of real-time data||Timing analysis of real-time data is possible because the Simulink model is running on the hardware in real-time.||Timing analysis of real-time data is not possible because the Simulink model is running in your computer and not on the hardware.|
|Code generation||Code is generated on the hardware.||No code is generated.|
To simulate a model in Connected I/O during Normal mode simulation, you must enable the Connected I/O option:
Open a Simulink model.
In the Simulink toolbar, set the Simulation mode to
In the MODELING tab, select Model Settings.
In the Configuration Parameters dialog box, select Hardware Implementation.
Set the Hardware board parameter to any Arduino
board listed in the Supported
Arduino Boards and Blocks with Connected I/O section. For
Arduino Mega 2560. This selection
automatically populates the parameters in the Hardware
board settings with the default values for the Arduino
From the Groups list under Target hardware resources, select Connected I/O.
Select the Enable Connected I/O option.
Click Apply. Click OK to close the dialog box.
Optionally, you can change the rate of simulation by enabling the Simulink Pacing Option as described in Simulation Pacing (Simulink).