lsqnonlinwith a Simulink® Model
This example shows how to tune the parameters of a Simulink model. The model,
optsim, is included in the
demos folder of your MATLAB® installation. The model includes a nonlinear process plant modeled as a Simulink block diagram.
Plant with Actuator Saturation
The plant is an under-damped third-order model with actuator limits. The actuator limits are a saturation limit and a slew rate limit. The actuator saturation limit cuts off input values greater than 2 units or less than –2 units. The slew rate limit of the actuator is 0.8 units/sec. The closed-loop response of the system to a step input is shown in Closed-Loop Response. You can see this response by opening the model (type
optsim at the command line or click the model name), and selecting Run from the Simulation menu. The response plots to the scope.
The problem is to design a feedback control loop that tracks a unit step input to the system. The closed-loop plant is entered in terms of the blocks where the plant and actuator are located in a hierarchical Subsystem block. A Scope block displays output trajectories during the design process.
To solve this problem, minimize the error between the output and the input signal. (In contrast, in the example Using fminimax with a Simulink® Model, the solution involves minimizing the maximum value of the output.) The variables are the parameters of the Proportional Integral Derivative (PID) controller. If you only need to minimize the error at one time unit, you would have a scalar objective function. But the goal is to minimize the error for all time steps from 0 to 100, thus producing a multiobjective function (one function for each time step).
lsqnonlin to perform a least-squares fit on the tracking of the output. The tracking is performed by the function
tracklsq, which is nested in
runtracklsq at the end of this example.
tracklsq returns the error signal
yout, the output computed by calling
sim, minus the input signal 1.
runtracklsq sets up all required values and then calls
lsqnonlin with the objective function
tracklsq. The variable
options passed to
lsqnonlin defines the criteria and display characteristics. The options specify to have no displayed output, to use the
'levenberg-marquardt' algorithm, and the options give termination tolerances for the step and objective function on the order of 0.001.
To run the simulation in the model
optsim, you must specify the variables
a2 are variables in the Plant block).
Kd are the variables to be optimized. The function
tracklsq is nested inside
runtracklsq so that the variables
a2 are shared between the two functions. The variables
a2 are initialized in
The objective function
tracklsq runs the simulation. You can run the simulation either in the base workspace or the current workspace, that is, the workspace of the function calling
sim, which in this case is the workspace of
tracklsq. In this example, the
SrcWorkspace option is set to
'Current' to tell
sim to run the simulation in the current workspace.
runtracklsq runs the simulation to 100 seconds.
When the simulation is complete,
runtracklsq creates the
myobj object in the current workspace (that is, the workspace of
tracklsq). The Outport block in the block diagram model puts the
yout field of the object into the current workspace at the end of the simulation.
When you run
runtracklsq, the optimization gives the solution for the proportional, integral, and derivative (
Kd) gains of the controller.
[Kp, Ki, Kd] = runtracklsq
Kp = 3.1330
Ki = 0.1465
Kd = 14.3918
The scope shows the optimized closed-loop step response.
Closed-Loop Response After
Note: The call to
sim results in a call to one of the Simulink ordinary differential equation (ODE) solvers. You need to choose which type of solver to use. From the optimization point of view, a fixed-step ODE solver is the best choice if it is sufficient to solve the ODE. However, in the case of a stiff system, a variable-step ODE method might be required to solve the ODE.
The numerical solution produced by a variable-step solver, however, is not a smooth function of parameters, because of step-size control mechanisms. This lack of smoothness can prevent an optimization routine from converging. The lack of smoothness is not an issue when you use a fixed-step solver. (For a further explanation, see .)
Simulink Design Optimization™ software is recommended for solving multiobjective optimization problems in conjunction with Simulink variable-step solvers. This software provides a special numeric gradient computation that works with Simulink and avoids introducing a problem of lack of smoothness.
The following code creates the
runtracklsq helper function.
function [Kp,Ki,Kd] = runtracklsq % RUNTRACKLSQ demonstrates using LSQNONLIN with Simulink. mdl = 'optsim'; open_system(mdl) % Load the model in = Simulink.SimulationInput(mdl); % Create simulation input object in = in.setModelParameter('StopTime','100'); % Stop time 100 pid0 = [0.63 0.0504 1.9688]; % Initial gain values a1 = 3; a2 = 43; % Initialize model plant variables options = optimoptions(@lsqnonlin,'Algorithm','levenberg-marquardt',... 'Display','off','StepTolerance',0.001,'OptimalityTolerance',0.001); % Optimize the gains set_param(mdl,'FastRestart','on'); % Fast restart pid = lsqnonlin(@tracklsq,pid0,,,options); set_param(mdl,'FastRestart','off'); % Return the gains Kp = pid(1); Ki = pid(2); Kd = pid(3); function F = tracklsq(pid) % Track the output of optsim to a signal of 1 % Set the simulation input object parameters in = in.setVariable('Kp',pid(1),'Workspace',mdl); in = in.setVariable('Ki',pid(2),'Workspace',mdl); in = in.setVariable('Kd',pid(3),'Workspace',mdl); % Simulate out = sim(in); F = out.get('yout') - 1; end end
Copyright 2019–2020 The MathWorks, Inc.