scanI2CBus

Scan I2C bus device addresses

collapse all in page

Add-On Required: This feature requires the MATLAB Support Package for Raspberry Pi Hardware add-on.

Syntax

[i2cAddresses] = scanI2CBus(mypi)
[i2cAddresses] = scanI2CBus(mypi,Bus)

Description

[i2cAddresses] = scanI2CBus(mypi) returns a list of addresses for devices connected to the I2C bus.

example

[i2cAddresses] = scanI2CBus(mypi,Bus) returns a list of addresses for devices connected to the specified I2C bus.

example

Examples

collapse all

You can connect and exchange data with a pair of I2C devices.

Create a connection from the MATLAB® software to the Raspberry Pi® board.

mypi = raspi
mypi = 

  Raspi with Properties:

           DeviceAddress: 'raspberrypi-hysdu8X38o'
                    Port: 18725
               BoardName: 'Raspberry Pi Model B Rev 2'
           AvailableLEDs: {'led0'}
    AvailableDigitalPins: [4 7 8 9 10 11 14 15 17 18 22 23 24 25 27 30 31]
    AvailableSPIChannels: {}
      AvailableI2CBuses:  {'i2c-0'  'i2c-1'}
             I2CBusSpeed: 100000

  Supported peripherals

Redisplay AvailableI2CBuses and I2CBusSpeed.

mypi.AvailableI2CBuses
mypi.I2CBusSpeed      
ans =

  1×2 cell array 

    {'i2c-0'}    {'i2c-1'}

ans =

      100000

Show the location of the I2C pins.

showPins(mypi)

The pin map shows that, for this model and revision of the board, the i2c-1 bus is available on the GPIO header pins I2C1_SDA (GPIO 2) and I2C1_SCL (GPIO 3).

After physically connecting your I2C device to the I2C pins, get the addresses of I2C devices attached to the I2C bus, 'i2c-1'.

scanI2CBus(mypi,'i2c-1')

ans =

  1×2 cell array  

     {'0x55'}    {'0x20'}

Create a connection, i2csensor, from the MATLAB software to the I2C sensor at '0x20'.

i2csensor = i2cdev(mypi,'i2c-1','0x20')

i2csensor = 

I2Cdev with properties:

        Bus: 'i2c-1'
    Address: 32

Read two uint8 numbers from the sensor.

output1 = read(i2csensor,2)

Read the value of register 14 from the sensor.

output2 = readRegister(i2csensor,14)

Create a connection, i2cdisplay, from the MATLAB software to the I2C LED display at '0x55'.

i2cdisplay = i2cdev(mypi,'i2c-1','0x55')

i2cdisplay = 

I2Cdev with properties:

        Bus: 'i2c-1'
    Address: 85

Write characters to the display.

write(i2cdisplay,[hex2dec('20') hex2dec('51')])

Write a scalar hexadecimal value, hex2dec('08'), to register 3 on an I2C device.

writeRegister(i2cdisplay,3,hex2dec('08'),'uint8')

If you are not using I2C, disable I2C using the Hardware Setup Screen to free additional GPIO pins. Before using I2C again, enable I2C and change the I2C bus speed using the Hardware Setup screen. In this example the bus speed is set to 400000 bits/s.

mypi.I2CBusSpeed
ans =

       400000

Input Arguments

collapse all

Connection to the Raspberry Pi hardware board, specified as a raspi object.

The identifier of the I2C bus connected to the hardware, specified as a character vector. This property is set by the bus input argument, and it cannot be changed after object creation.

Example: 'i2c-1'

Data Types: char

Output Arguments

collapse all

I2C device addresses, returned as a cell of hex values.

See Also

| | | | | |

Topics

External Websites