Answered
What's Remap ePWMs for DMA access (Requires silicon revision A and above) means?
Hi Xu, From device data sheet if the silicon version is >='A' then we have the following details. "By default, ePWM and HRPW...

nästan 5 år ago | 0

Answered
Viewing IQ Math variables in Scope of Matlab Simulink
Hi Sachin, Please find the attached model which is created in 2019a version of MATLAB. We have used fixdt(1, 32, 19) data type...

nästan 5 år ago | 0

| accepted

Answered
Issue for TI c2000 package in Matlab2017a?
Hi Qing Liu, Please can you specify sample time for constant block to -1 and try. In that case the block inherits the model st...

nästan 5 år ago | 1

| accepted

Answered
Simulink C caller block can't compile C code, but other blocks can
Hi Matthew, Attached is the model which now compiles with C caller block. Please note changes made to Simulation target and ...

nästan 5 år ago | 0

| accepted

Answered
How to write at specific memory location of C2000 using Matlab Function in Siumulink Embedded Coder?
Hi Sumit, One apporach is to define the register access in a 'c' function in a 'c' source file. You can then call this functi...

nästan 5 år ago | 0

| accepted

Answered
Simulink C caller block can't compile C code, but other blocks can
Hi Matthew, Please can you attach the model to help us investigate further. Regards, Venkatesh C

nästan 5 år ago | 0

Answered
rtwtypes.h not created
Hi, Please contact us at: https://www.mathworks.com/support/contact_us.html Regards, Venkatesh C

nästan 5 år ago | 0

Answered
Simulink - F28335 eQEP block is not working properly
Hi Omer, Please verify if the GPIO configuration are done accordingly in the hardware config pane. Regards, Venkatesh C

nästan 5 år ago | 0

| accepted

Answered
F28379D DRV8301 current sense problem
Hi, Please contact us at: https://www.mathworks.com/support/contact_us.html Regards, Venkatesh C

nästan 5 år ago | 0

Answered
eCAN received message status
Hi, Here is the clue. https://www.mathworks.com/matlabcentral/answers/456443-how-do-i-read-the-output-of-the-comp-block-for-a-...

nästan 5 år ago | 0

Answered
Why doesn't the A2L file from the CCP block of C2000 Embedded Coder Support Package have the part of DAQ list?
Hi, Please connect to us at: https://www.mathworks.com/support/contact_us.html Regards, Venkatesh C

nästan 5 år ago | 0

Answered
Why doesn't the A2L file from the CCP block of C2000 Embedded Coder Support Package have the part of DAQ list?
Hi, Please check our example model at: https://www.mathworks.com/help/supportpkg/texasinstrumentsc2000/examples/can-calibratio...

nästan 5 år ago | 0

| accepted

Answered
Setting DMA with ADC in f28335 using TI C2000 support package
Hi, This feature is introdcued in R2018b. We provide release notes which contains a list of features and Bug Fixes for the giv...

nästan 5 år ago | 0

| accepted

Answered
eCAN received message status
Hi, Each of the available mail box can trigger the interrupt when they send/receive the CAN message. The mail box that caused ...

nästan 5 år ago | 0

Answered
eCAN received message status
Hi, You may probably try to use the C28x Hardware interrupt block and react to a recieved CAN message by reading the same. Use ...

nästan 5 år ago | 0

Answered
Setting DMA with ADC in f28335 using TI C2000 support package
Hi, Please check this page. https://in.mathworks.com/help/supportpkg/texasinstrumentsc2000/ug/modify-epwm-using-dma.html Rega...

nästan 5 år ago | 0

Answered
Why can't the CCP block of C2000 Embedded Coder Support Package work?
Hi, Our examples are tested to work with Vector Hardware only. Please refer the below post for the same: https://in.mathworks....

nästan 5 år ago | 0

| accepted

Answered
C2000 Hardware Support Package IPC Error
Hi, Thanks for pointing it out. We will fix it in next update. Regards, Venkatesh C

nästan 5 år ago | 0

Answered
Same code, new LAUNCHXL-F28379D memory issue
Hi, Can you please take a look at this post: https://in.mathworks.com/matlabcentral/answers/458008-flash-programming-ti-launch...

nästan 5 år ago | 1

Answered
Reset eCAP value when the input signal off
Hi, Please refer this example 'c28035pmsmfoc_ert' we have eCAP block implemention under 'c28035pmsmfoc_ert/Hall Sensor A'. R...

nästan 5 år ago | 0

Answered
How do I roll back C2000 hardware support package version?
Hi Matthew, Can you help us understand what is not working with (18.2.2) so that we can take a look in to the same. Please not...

nästan 5 år ago | 0

Answered
C code won't compile for C caller but will run in other blocks
Hi Matthew, Please try contacting MathWorks support at: https://www.mathworks.com/support/contact_us.html Regards, Venkatesh...

nästan 5 år ago | 0

Answered
Flash programming TI LAUNCHXL-F28379D
Hi Marco/Rfymat, Please can you try installing the CCSv8.2. http://processors.wiki.ti.com/index.php/Download_CCS And configur...

nästan 5 år ago | 0

Answered
Logging data with TI F28379D C2000 development board in Simulink
Hi, Please use the below script to stitch the files to one MAT file. varName = 'ScopeData2'; list = dir(fullfile('C:/yyy/ma...

nästan 5 år ago | 1

Answered
Logging data with TI F28379D C2000 development board in Simulink
Hi, Please try 'Data Logging' section at below link: https://in.mathworks.com/help/supportpkg/texasinstrumentsc2000/examples/p...

nästan 5 år ago | 0

Answered
How can I read data via SCI and display it in Simulink?
Hi, Please checkout the 2 model approach at page: https://in.mathworks.com/help/supportpkg/texasinstrumentsc2000/examples/...

nästan 5 år ago | 0

Answered
unable to interface C2000 piccolo F280049C with Matlab 2018a... showing error in check status in command window.
Hi, checkEnvSetup is old workflow, please can you try using the steps as captured below and configure the device. 1) Select ...

nästan 5 år ago | 0

Answered
F28335 Timer1 & Timer2 Construction - Using via Simulink
Hi, Use of Timer1 and Timer2 may not be possible directly from simulink using modelling approach. Instead a custom code appr...

nästan 5 år ago | 0

Answered
Embedded Coder for C2000
Yes, along with 'install' option for the support package, we also provide 'download' option. That should help you to download t...

ungefär 5 år ago | 0

Answered
Is it possible for me to use the same F2837x GPIO pin as input and an output in Simulink?
Hi Farhan, Yes, you can achieve this configuration in simulink. To begin with you may need to add the following lines of code ...

ungefär 5 år ago | 2

| accepted