Answered
link a full bridge DC/AC to an induction machine
Hello Ayoub, you are using a block specifically designed to be the arm of a multi-level converter, It is not a standard full b...

ungefär 2 år ago | 0

| accepted

Answered
Difference in Boost Converter Waveforms
Hey Andy, please send me an email to jvansick@mathworks.com. Regards, Joel

mer än 2 år ago | 0

| accepted

Answered
How to modelling and measure an algorithmic potentiometer in Matlab
Hello Derek, the appropriate way to model potentiometer response is using Simscape. If you are having trouble with Simscape, I...

mer än 2 år ago | 0

Answered
what if Stand-Alone Solar PV System with AC and DC loads with Battery Backup
Hello Alisher, you can use that as a starting place, but it doesn't have any AC power in it. Modifying it is possible, but wou...

mer än 2 år ago | 0

Answered
my firing angle on this triac does not work correctly ?
My first guess would be that you need to double the rate of your firing. It looks like you are triggering the first thyristor c...

mer än 2 år ago | 0

Answered
HDL Code Generation (Verilog) for a 2-D Lookup Table
Hello, you can go through examples like this for generating hdl: https://www.mathworks.com/help/hdlcoder/gs/example-generating-...

mer än 2 år ago | 0

Answered
No me abre MATLAB
This question has been resolved by downloading the most recent version, see comments section above.

mer än 2 år ago | 0

| accepted

Answered
How to rectify my AC Voltage?
it's possible your load is too large (resistance too small) and the piezoelectric device isn't powerful enough to charge it. Yo...

mer än 2 år ago | 0

Answered
Can Matlab software simulate different grades of fuels burning in an Large Diesel Engine?
The tools could be used to create this type of simulation, but you'd have to build it from the ground up.

mer än 2 år ago | 0

Answered
Problem with DC voltage output from Boost type converter when adding another to its output.
It looks like you are using open loop control and the first converter is supplying it's original load PLUS the new load of the s...

mer än 2 år ago | 1

Answered
Can I cange the step size from fixed to variable after a certain simulation time?
Hello Annette, unfortunately, there is no way to do this. In general, it's best to only simulate a few cycles with the n-chann...

mer än 2 år ago | 0

Answered
Why does my Simulink model terminate (CANBUS communication) without reaching the end of its simulation?
Hello Zubair, if it works when the motors aren't screwed down, and isolated by tape, and fails when they are screwed down while...

mer än 2 år ago | 0

Answered
How do I customize an Electrical Simscape block?
Hello Jose, that block is a fundamental RLC block so it cannot be customized. You could customize the dynamic three phase load...

mer än 2 år ago | 0

Answered
Lithium ion battery modelling
I would start with this blocK: https://www.mathworks.com/help/physmod/sps/ref/batterytablebased.html this block will let you ch...

mer än 2 år ago | 0

Answered
how to create a three-phase non-linear load with specific harmonics 3,5,7,9,11,15?
You would have to create those waveforms yourself using a controlled source. you could use simulink to add together different s...

mer än 2 år ago | 0

Answered
How to graph an entire simulink scope plot without the scope plot slowly ticking through the simulation.
Hello Mark, there is no way to get a plot without running the simulation as without the simulation, there is no data. You are ...

mer än 2 år ago | 0

Answered
I can not find FACTS devices in SIMSCAPE Electrical 2021b.
A number of more complicated blocks have been moved to examples instead of librarly blocks. Please start by looking here: https...

mer än 2 år ago | 0

Answered
When I input higher solar irradiance into my solar cell, its giving me a lower electrical efficiency; this doesn't seem right?
Hello Jason, this example uses a very simple electrical model that isn't ussing MPPT. Without MPPT, efficiency doesn't necessa...

mer än 2 år ago | 0

Answered
Matlab compiler - matlabruntimeforpython : "Dot indexing is not supported for variables of this type" when calling sim()
The sim command is not supported by the matlab compiler. You need the Simulink compiler for that OR you need to use embedded co...

mer än 2 år ago | 0

| accepted

Answered
Simulation of electric field of parallel plate capacitor
https://www.mathworks.com/matlabcentral/fileexchange/37923-2d-electric-potential-field-in-parallel-plates-capacitor

mer än 2 år ago | 0

Answered
How to make "ups" using simulink.
You can connect the models. You would typically connect them with a dc link with a battery. Here is a shipping example of a si...

mer än 2 år ago | 0

Answered
How to model a medium transmission line for both nominal pi and t sections
Hello Salah, to start, I would just set them to your positive sequence values (this is incorrect, but will get you started with...

mer än 2 år ago | 1

| accepted

Answered
How to implement Induction motor to a system?
Hello Ozan, the best way to do this is to start over and use simscape to model the whole physical system so that you don't have...

mer än 2 år ago | 0

Answered
Why aging of generic battery model is inconsistent with respect to battery initial state-of-charge?
It looks like your data sets are following two linear lines and results fall either on the top or bottom one. If you look at yo...

mer än 2 år ago | 0

| accepted

Answered
Problem At Sistem On Chip (SOC,PIL) Example Application
If the software recommendations made by above commenters don't work, consider a hardware/connection issue. Can you send a photo...

mer än 2 år ago | 1

| accepted

Answered
How to add a low Bandwidth Communication in Simulink
Hello Hussain, if you want the delay to be disreet, you can use a rate transition block to use unit delays at different time st...

mer än 2 år ago | 0

Answered
Missing Motor-CAD file in Simulink Example
Hello Klemen, apparently the model does not ship with the example. Sorry about that. Here is the model. Joel

mer än 2 år ago | 1

| accepted

Answered
Error with the PV array simulation
Hello Jung, you are applying a constantly increasing voltage to the output of the solar cell, so you couldn't get a fixed volta...

mer än 2 år ago | 0

| accepted

Answered
Error for compiling Simscape network for model Astable.
I wasn't able to figure out what was wrong by looking at it. It would seem a parameter was entered with the wrong unit type, bu...

mer än 2 år ago | 0

Answered
How do I access the stress, strain and moment variables from the Piezo Bender Simscape Block for use in a Simulink simulation?
Hello Christopher, To look at more data after the simulaiton, you can use the simscape results explorer. Right click the piezo...

mer än 2 år ago | 1