Verify Viterbi Decoder Using MATLAB System Object and HDL Simulator

This example shows you how to use MATLAB® System objects and Mentor Graphics® ModelSim®/QuestaSim® or Cadence® Incisive®/Xcelium® to cosimulate a Viterbi decoder implemented in VHDL.

Set Simulation Parameters and Instantiate Communication System Objects

If you are using Incisive/Xcelium, set simulator variable to 'Incisive'

Simulator = 'Incisive';

% or if you are using ModelSim/QuestaSim, set simulator variable to
% 'ModelSim'
Simulator = 'ModelSim';

% The following code sets up the simulation parameters and instantiates the
% system objects that represent the channel encoder, BPSK modulator, AWGN
% channel, BPSK demodulator, and error rate calculator. Those objects
% comprise the system around the Viterbi decoder and can be thought of as
% the test bed for the Viterbi HDL implementation.

EsNo = 0;	% Energy per symbol to noise power spectrum density ratio in dB
FrameSize = 1024;  % Number of bits in each frame

% Convolution Encoder
hConEnc = comm.ConvolutionalEncoder;
% BPSK Modulator
hMod    = comm.BPSKModulator;
% AWGN channel
hChan   = comm.AWGNChannel('NoiseMethod', ...
                           'Signal to noise ratio (Es/No)',...
% BPSK demodulator
hDemod  = comm.BPSKDemodulator('DecisionMethod','Log-likelihood ratio',...
% Error Rate Calculator
hError  = comm.ErrorRate('ComputationDelay',100,'ReceiveDelay', 58);

Instantiate the Cosimulation System Object

The hdlcosim function returns an HDL cosimulation System object, which represents the HDL implementation of the Viterbi decoder in this simulation system.

switch Simulator
    case 'ModelSim'
        hDec    = hdlcosim('InputSignals', {'/viterbi_block/In1','/viterbi_block/In2'}, ...
                           'OutputSignals', {'/viterbi_block/Out1'}, ...
                           'OutputSigned', false, ...
                           'OutputFractionLengths', 0, ...
                           'TCLPreSimulationCommand', 'force /viterbi_block/clk_enable 1 0; force /viterbi_block/clk 0 0 ns, 1 5 ns -repeat 10 ns; force /viterbi_block/reset 1 0 ns, 0 8 ns; ', ...
                           'TCLPostSimulationCommand', 'echo "done";', ...
                           'PreRunTime', {10,'ns'}, ...
                           'Connection', {'Shared'}, ...
                           'SampleTime', {10,'ns'});
    case 'Incisive'
        hDec    = hdlcosim('InputSignals', {'/viterbi_block/In1','/viterbi_block/In2'}, ...
                           'OutputSignals', {'/viterbi_block/Out1'}, ...
                           'OutputSigned', false, ...
                           'OutputFractionLengths', 0, ...
                           'TCLPreSimulationCommand', 'force :clk B"0" -after 0ns B"1" -after 5ns -repeat 10ns; force reset B"1" -after 0ns B"0" -after 8ns; force :clk_enable B"1" -after 0ns', ...
                           'TCLPostSimulationCommand', 'echo "done";', ...
                           'PreRunTime', {10,'ns'}, ...
                           'Connection', {'Shared'}, ...
                           'SampleTime', {10,'ns'});

Launch HDL Simulator

The vsim and nclaunch command launches HDL simulator. The launched HDL simulator session compiles the HDL design and loads the HDL simulation. You are ready to perform cosimulation when the HDL simulation is fully loaded in simulator.

disp('Waiting for HDL simulator to launch ...');
switch Simulator
    case 'ModelSim'
    case 'Incisive'
processid = pingHdlSim(Timeout);
% Check if HDL simulator is ready for Cosimulation.
assert(ischar(processid),['Timeout: HDL simulator took more than ', num2str(Timeout),' seconds to setup,please increase the timeout in ''pingHdlSim''']);
disp('Ready for cosimulation ...');

Run Cosimulation

This example simulates the BPSK communication system in MATLAB incorporating the Viterbi decoder HDL implementation via the cosimulation System object. This section of the code calls the processing loop to process the data frame-by-frame with 1024 bits in each data frame.

for counter = 1:20480/FrameSize
    data            = randi([0 1],FrameSize,1);
    encodedData     = step(hConEnc, data);
    modSignal       = step(hMod, encodedData);
    receivedSignal  = step(hChan, modSignal);
    demodSignalSD   = step(hDemod, receivedSignal);
    quantizedValue  = fi(4-demodSignalSD,0,3,0);
    input1          = quantizedValue(1:2:2*FrameSize);
    input2          = quantizedValue(2:2:2*FrameSize);
    receivedBits    = step(hDec,input1, input2);
    errors          = step(hError, data, double(receivedBits));

Display the Bit-Error Rate

The Bit-Error Rate is displayed for the Viterbi decoder.

sprintf('Bit Error Rate is %d\n',errors(1))

Destroy Cosimulation System Object to Release HDL Simulator

The HDL simulator is unblocked when the HDL cosimulation system object is destroyed in MATLAB. Close the HDL simulator session manually.

clear hDec;

% This concludes the "Verify Viterbi Decoder Using MATLAB System Object and
% HDL Simulator".