SpectrumAnalyzerConfiguration

Configure Spectrum Analyzer block

Description

The `spbscopes.SpectrumAnalyzerConfiguration` object contains the scope configuration information for the Spectrum Analyzer block.

Creation

`MyScopeConfiguration = get_param(gcbh,'ScopeConfiguration')` constructs a new Spectrum Analyzer Configuration object. You must first select the block in the model or give the full path to the block.

Properties

expand all

Frequently Used

Number of input ports on a scope block, specified by a character vector or string scalar. Maximum number of input ports is 96.

Data Types: `char` | `string`

The domain of the input signal you want to visualize. If you visualize time-domain signals, the signal is transformed to the frequency spectrum based on the algorithm specified by the `Method` parameter.

Scope Window Use

Open the Spectrum Settings. In the Main options section, set Input Domain.

Data Types: `char` | `string`

Specify the spectrum type to display.

`"Power"` — Power spectrum

`"Power density"` — Power spectral density. The power spectral density is the magnitude squared of the spectrum normalized to a bandwidth of 1 hertz.

`"RMS"` — Root mean square. The root-mean-square shows the square root of the mean square. This option is useful when viewing the frequency of voltage or current signals.

Tunable: Yes

Scope Window Use

Open the Spectrum Settings. In the Main options section, set Type.

Data Types: `char` | `string`

Specify the spectrum type as one of `"Spectrum"`, `"Spectrogram"`, or `"Spectrum and spectrogram"`.

• `"Spectrum"` — shows the power spectrum.

• `"Spectrogram"` — shows frequency content over time. Each line of the spectrogram is one periodogram. Time scrolls from the bottom to the top of the display. The most recent spectrogram update is at the bottom of the display.

• `"Spectrum and Spectrogram"` — shows a dual view of a spectrum and spectrogram.

Tunable: Yes

Scope Window Use

Open the Spectrum Settings. In the Main options section, set View.

Data Types: `char` | `string`

Specify the source of the input sample rate as:

• `"Inherited"` — Spectrum Analyzer inherits the input sample rate from the model.

• `"Property"` — Specify the sample rate input directly using the `SampleRate` property.

Data Types: `char` | `string`

Specify the sample rate of the input signals in hertz as a character vector or string scalar.

Dependency

To enable this property, set `SampleRateSource` to `"Property"`.

Data Types: `char` | `string`

Specify the spectrum estimation method as `Welch` or ```Filter bank```.

Dependency

To enable this property, set `InputDomain` to `"Time"`.

Scope Window Use

Open the Spectrum Settings. In the Main options section, set Method.

Data Types: `char` | `string`

• `true` — Compute and plot two-sided spectral estimates. When the input signal is complex-valued, you must set this property to `true`.

• `false` — Compute and plot one-sided spectral estimates. If you set this property to `false`, then the input signal must be real-valued.

When this property is `false`, Spectrum Analyzer uses power-folding. The y-axis values are twice the amplitude that they would be if this property were set to `true`, except at `0` and the Nyquist frequency. A one-sided power spectral density (PSD) contains the total power of the signal in the frequency interval from DC to half of the Nyquist rate. For more information, see `pwelch`.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, select Two-sided spectrum.

Data Types: `logical`

• `"Log"` — displays the frequencies on the x-axis on a logarithmic scale. To use the `"Log"` setting, you must also set the `PlotAsTwoSidedSpectrum` property to `false`.

• `"Linear"` — displays the frequencies on the x-axis on a linear scale. To use the `"Linear"` setting, you must also set the `PlotAsTwoSidedSpectrum` property to `true`.

Tunable: Yes

Scope Window Use

Open the Spectrum Settings. In the Trace options section, set Scale.

Data Types: `char` | `string`

• `"Full"` - The Spectrum Analyzer computes and plots the spectrum over the entire Nyquist frequency interval.

• `"Span and center frequency"` - The Spectrum Analyzer computes and plots the spectrum over the interval specified by the `Span` and `CenterFrequency` properties.

• `"Start and stop frequencies"` - The Spectrum Analyzer computes and plots the spectrum over the interval specified by the `StartFrequency` and `StopFrequency` properties.

Tunable: Yes

Scope Window Use

Open the Spectrum Settings. In the Main options section, select Full frequency span for `"Full"`. Otherwise, clear the Full frequency span check box and choose between `Span` or `FStart`.

Data Types: `char` | `string`

Specify (as a character vector or string scalar) the frequency span, in hertz, over which the Spectrum Analyzer computes and plots the spectrum. The overall span, defined by this property and the `CenterFrequency` property, must fall within the Nyquist frequency interval.

Dependency

To enable this property, set `FrequencySpan` to `"Span and center frequency"`.

Data Types: `char` | `string`

Specify (as a character vector or string scalar) the frequency center, in hertz, over which the Spectrum Analyzer computes and plots the spectrum. The overall frequency span, defined by the `Span` and this property, must fall within the Nyquist frequency interval.

Dependency

To enable this property, set `FrequencySpan` to `"Span and center frequency"`.

Data Types: `char` | `string`

Start of the frequency interval over which spectrum is computed, specified in hertz as a character vector or string scalar of a real scalar. The overall span, which is defined by this property and `StopFrequency`, must fall within the Nyquist frequency interval.

Dependency

To enable this property, set `FrequencySpan` to `"Start and stop frequencies"`.

Data Types: `char` | `string`

End of the frequency interval over which spectrum is computed, specified in hertz as a character vector or string scalar of a real scalar. The overall span, which is defined by this property and the `StartFrequency` property, must fall within the Nyquist frequency interval.

Dependency

To enable this property, set `FrequencySpan` to `"Start and stop frequencies"`.

Scope Window Use

Open the Spectrum Settings. In the Main options section, clear the Full frequency span and change `Span` to `FStart`. Set FStop (Hz).

Data Types: `char` | `string`

Specify the frequency resolution method of the Spectrum Analyzer.

• `"RBW"` - The `RBWSource` and `RBW` properties control the frequency resolution (in Hz) of the analyzer. The FFT length is the window length that results from achieving the specified RBW value or 1024, whichever is larger.

• `"WindowLength"` - Applies only when the `Method` property is set to `"Welch"`. The `WindowLength` property controls the frequency resolution. You can control the number of FFT points only when the `FrequencyResolutionMethod` property is `"WindowLength"`.

• `"NumFrequencyBands"` - Applies only when the `Method` property is set to ```"Filter Bank"```. The `FFTLengthSource` and `FFTLength` properties control the frequency resolution.

Tunable: Yes

Dependency

To enable this property, set `InputDomain` to `"Time"`.

Scope Window Use

Open the Spectrum Settings. In the Main options section, set the frequency resolution method by selecting the RBW (Hz) dropdown.

Data Types: `char` | `string`

Specify the source of the resolution bandwidth (RBW) as `"Auto"`, `"Property"`, or `"InputPort"`.

• `"Auto"` — The Spectrum Analyzer adjusts the spectral estimation resolution to ensure that there are 1024 RBW intervals over the defined frequency span.

• `"Property"` — Specify the resolution bandwidth directly using the `RBW` property.

• `"InputPort"` — An input port is added to the Spectrum Analyzer block to read the RBW. This option is only applicable to frequency input.

Dependencies

To enable this property, set:

• `InputDomain` to `"Time"` and `FrequencyResolutionMethod` to `"RBW"`.

• `InputDomain` to `"Frequency"`.

Data Types: `char` | `string`

RBW controls the spectral resolution of the Spectrum Analyzer. Specify the resolution bandwidth in hertz as a character vector or string scalar. You must specify a value to ensure that there are at least two RBW intervals over the specified frequency span. Thus, the ratio of the overall span to RBW must be greater than two:

`$\frac{span}{RBW}>2$`

You can specify the overall span in different ways based on how you set the `FrequencySpan` property.

Dependency

To enable, set:

• `RBWSource` to `"Property"`

Data Types: `char` | `string`

Control the frequency resolution by specifying the window length in samples used to compute the spectral estimates. The window length must be an integer scalar greater than 2, specified as a character vector or string scalar.

Dependencies

To enable this property, set:

• `FrequencyResolutionMethod` to `"WindowLength"`, which controls the frequency resolution based on your window length setting.

• `Method` to `"Welch"`.

Data Types: `char` | `string`

• `"Auto"` - sets the FFT length to the window length specified in the `WindowLength` property or 1024, whichever is larger.

• `"Property"` - number of FFT points using the `FFTLength` property. `FFTLength` must be greater than `WindowLength`.

Tunable: Yes

Dependency

To enable this property, set `FrequencyResolutionMethod` to `"WindowLength"`.

Scope Window Use

Open the Spectrum Settings. In the Main options section, next to the RBW (Hz) option, enter a number or select `Auto`.

Data Types: `char` | `string`

Specify the length of the FFT that the Spectrum Analyzer uses to compute spectral estimates.

If `FrequencyResolutionMethod` is `"RBW"`, the FFT length is set as the window length required to achieve the specified resolution bandwidth value or 1024, whichever is larger.

Dependencies

To use this property, the following must be true:

• `FFTLength` value is greater than or equal to the `WindowLength`.

• `FrequencyResolutionMethod` is set to `"WindowLength"` or `"NumFrequencyBands"`

• `FFTLengthSource` is set to `"Property"`.

Data Types: `char` | `string`

Specify the number of filter taps or coefficients for each frequency band as a character vector or a string scalar. This number must be a positive even integer. This value corresponds to the number of filter coefficients per polyphase branch. The total number of filter coefficients is equal to `NumTapsPerBand` + `FFTLength`.

Dependency

To enable this property, set `Method` to `"Filter Bank"`.

Data Types: `char` | `string`

• `"Auto"` — The frequency vector is calculated from the length of the input. See Frequency Vector.

• `"Property"` — Enter a custom vector as the frequency vector.

• `"InputPort"` — An input port appears on the block to read the frequency vector input.

Dependency

To enable this property, set `InputDomain` to `"Frequency"`.

Data Types: `char` | `string`

Set the frequency vector that determines the x-axis of the display. The vector must be monotonically increasing and of the same size as the input frame size.

Dependency

To enable this property, set `FrequencyVectorSource` to `"Property"`.

Scope Window Use

Open the Spectrum Settings. In the Frequency input options section, set Frequency (Hz).

Data Types: `single` | `double` | `int8` | `int16` | `int32` | `int64` | `uint8` | `uint16` | `uint32` | `uint64`

Select the units of the frequency-domain input. This property allows the Spectrum Analyzer to scale frequency data if you choose a different display unit with the `Units` property.

Dependency

This option is only available when `InputDomain` is set to `Frequency`.

Scope Window Use

Open the Spectrum Settings. In the Frequency input options section, set Input units.

Data Types: `char` | `string`

The percentage overlap between the previous and current buffered data segments, specified as a character vector or string scalar of a real scalar. The overlap creates a window segment that is used to compute a spectral estimate. The value must be greater than or equal to zero and less than 100.

Data Types: `char` | `string`

Specify a window function for the spectral estimator. The following table shows preset windows. For more information, follow the link to the corresponding function reference in the Signal Processing Toolbox™ documentation.

Window OptionCorresponding Signal Processing Toolbox Function
`"Rectangular"``rectwin`
`"Chebyshev"``chebwin`
`"Flat Top"``flattopwin`
`"Hamming"``hamming`
`"Hann"``hann`
`"Kaiser"``kaiser`
`"Blackman-Harris"``blackmanharris`

To set your own spectral estimation window, set this property to `"Custom"` and specify a custom window function in the `CustomWindow` property.

Tunable: Yes

Scope Window Use

Open the Spectrum Settings. In the Window options section, set Window.

Data Types: `char` | `string`

Specify a custom window function as a character array or string. The custom window function name must be on the MATLAB path. This property is useful if you want to customize the window using additional properties available with the Signal Processing Toolbox version of the window function.

Tunable: Yes

Example

Define and use a custom window function.

```function w = my_hann(L) w = hann(L, 'periodic') end scope.Window = 'Custom'; scope.CustomWindow = 'my_hann'```

Dependency

To use this property, set `Window` to `"Custom"`.

Scope Window Use

Open the Spectrum Settings. In the Window options section, in the Window option box, enter a custom window function name.

Data Types: `char` | `string`

The window sidelobe attenuation, in decibels (dB). The value must be greater than or equal to 45.

Dependency

To enable this property, set `Window` to `"Chebyshev"` or `"Kaiser"`.

Scope Window Use

Open the Spectrum Settings. In the Window options section, set Attenuation (dB).

Data Types: `char` | `string`

Specify the units in which the Spectrum Analyzer displays power values.

Tunable: Yes

Dependency

The available spectrum units depend on the value of `SpectrumType`.

`InputDomain``SpectrumType`Allowed `SpectrumUnits`
`Time``Power` or ```Power density````"dBFS"`, `"dBm"`, `"dBW"`, `"Watts"`
`RMS``"Vrms"`, `"dBV"`
`Frequency``"dBm"`, `"dBV"`, `"dBW"`, `"Vrms"`, `"Watts"`,

Scope Window Use

Open the Spectrum Settings. In the Trace options section, set Units.

Data Types: `char` | `string`

Specify the source of the dBFS scaling factor as either `"Auto"` or `"Property"`.

• `"Auto"` - The Spectrum Analyzer adjusts the scaling factor based on the input data.

• `"Property"` - Specify the full-scale scaling factor using the `FullScale` property.

Dependency

To enable this property, set `SpectrumUnits` to `"dBFS"`.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, set Full scale to `Auto` or enter a number.

Data Types: `char` | `string`

Specify a character vector or string scalar of a real positive scalar for the `dBFS` full scale.

Dependency

To enable this option set:

• `SpectrumUnits` to `"dBFS"`

• `FullScaleSource` to `"Property"`

Data Types: `char` | `string`

Specify the smoothing method as:

• `Running` — Running average of the last n samples. Use the `SpectralAverages` property to specify n.

• `Exponential` — Weighted average of samples. Use the `ForgettingFactor` property to specify the weighted forgetting factor.

Dependency

To enable this property, set `ViewType` to `"Spectrum"` or ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, set Averaging method.

Data Types: `char` | `string`

Specify the number of spectral averages as a character vector or string scalar. The Spectrum Analyzer computes the current power spectrum estimate by computing a running average of the last N power spectrum estimates. This property defines N.

Dependency

To enable this property, set `AveragingMethod` to `"Running"`.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, set Averages.

Data Types: `char` | `string`

Specify the exponential weighting as a scalar value greater than 0 and less than or equal to 1, specified as a string scalar or character vector.

Dependency

To enable this property, set `AveragingMethod` to `"Exponential"`.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, set Forgetting factor.

Data Types: `char` | `string`

Specify the load the scope uses as a reference to compute power levels.

Data Types: `char` | `string`

• Numeric scalar (specified as a character vector or string scalar) — Apply the same frequency offset to all channels, specified in hertz as a character vector.

• Numeric vector (specified as a character vector or string scalar) — Apply a specific frequency offset for each channel, specify a vector of frequencies. The vector length must be equal to number of input channels.

The frequency-axis values are offset by the values specified in this property. The overall span must fall within the Nyquist frequency interval. You can control the overall span in different ways based on how you set the `FrequencySpan` property.

Data Types: `char` | `string`

Set this property to `true` to treat M-by-1 and unoriented sample-based inputs as a column vector, or one channel. Set this property to `false` to treat M-by-1 and unoriented sample-based inputs as a 1-by-M row vector.

Data Types: `logical`

Spectrogram

Specify the channel for which the spectrogram is plotted, as a character vector or string scalar of a real, positive scalar integer in the range [1 N], where N is the number of input channels.

Dependency

To enable this property, set `ViewType` to `"Spectrogram"` or ```"Spectrum and spectrogram"```.

Data Types: `char` | `string`

Specify the source for the time resolution of each spectrogram line as either `"Auto"` or `"Property"`. The `TimeResolution` property shows the time resolution for the different frequency resolution methods and time resolution properties.

Tunable: Yes

Dependency

To enable this property, set `ViewType` to `"Spectrogram"` or ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Spectrum Settings. In the Spectrogram options section, set Time res (s).

Data Types: `char` | `string`

Specify the time resolution of each spectrogram line as a character vector or string scalar of a positive scalar, expressed in seconds.

The time resolution value is determined based on frequency resolution method, the RBW setting, and the time resolution setting.

MethodFrequency Resolution MethodFrequency Resolution SettingTime Resolution SettingResulting Time Resolution in Seconds
`Welch` or ```Filter Bank````RBW (Hz)``Auto``Auto`1/RBW
`Welch` or ```Filter Bank````RBW (Hz)``Auto`Manually enteredTime Resolution
`Welch` or ```Filter Bank````RBW (Hz)`Manually entered`Auto`1/RBW
`Welch` or ```Filter Bank````RBW (Hz)`Manually enteredManually enteredMust be equal to or greater than the minimum attainable time resolution, 1/RBW. Several spectral estimates are combined into one spectrogram line to obtain the desired time resolution. Interpolation is used to obtain time resolution values that are not integer multiples of 1/RBW.
`Welch``Window length``Auto`1/RBW
`Welch``Window length`Manually enteredMust be equal to or greater than the minimum attainable time resolution. Several spectral estimates are combined into one spectrogram line to obtain the desired time resolution. Interpolation is used to obtain time resolution values that are not integer multiples of 1/RBW.
`Filter Bank``Number of frequency bands``Auto`1/RBW
`Filter Bank``Number of frequency bands`Manually enteredMust be equal to or greater than the minimum attainable time resolution, 1/RBW.

Dependency

To enable this property, set:

• `ViewType` to `"Spectrogram"` or `"Spectrum and spectrogram"`

• `TimeResolutionSource` to `"Property`.

Data Types: `char` | `string`

Specify the source for the time span of the spectrogram as either `"Auto"` or `"Property"`. If you set this property to `"Auto"`, the spectrogram displays 100 spectrogram lines at any given time. If you set this property to `"Property"`, the spectrogram uses the time duration you specify in seconds in the `TimeSpan` property.

Tunable: Yes

Dependency

To enable this property, set `ViewType` to `"Spectrogram"` or ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Spectrum Settings. In the Spectrogram options section, set Time span (s).

Data Types: `char` | `string`

Specify the time span of the spectrogram display in seconds. You must set the time span to be at least twice as large as the duration of the number of samples required for a spectral update.

Dependency

To enable this property, set:

• `ViewType` to `"Spectrogram"` or ```"Spectrum and spectrogram"```.

• `TimeSpanSource` to `"Property"`.

Data Types: `char` | `string`

Measurements

Channel over which the measurements are obtained, specified as a character vector or a string scalar which evaluates to a positive integer greater than 0 and less than or equal to 100. The maximum number you can specify is the number of channels (columns) in the input signal.

Tunable: Yes

Data Types: `char` | `string`

Specify whether to display upper and lower spectral mask lines on a spectrum plot. This property uses properties from a `SpectralMaskSpecification` object to enable and configure the spectral masks.

Tunable: Yes

Scope Window Use

Open the Spectral Mask pane and modify the Settings options.

Enable peak finder to compute and display the largest calculated peak values. The `PeakFinder` property uses the `PeakFinderSpecification` properties.

The `PeakFinderSpecification` properties are:

• `MinHeight` –– Level above which peaks are detected, specified as a scalar value.

Default: `-Inf`

• `NumPeaks` –– Maximum number of peaks to show, specified as a positive integer scalar less than 100.

Default: `3`

• `MinDistance` –– Minimum number of samples between adjacent peaks, specified as a positive real scalar.

Default: `1`

• `Threshold` –– Minimum height difference between peak and its neighboring samples, specified as a nonnegative real scalar.

Default: `0`

• `LabelFormat` –– Coordinates to display next to the calculated peak value, specified as a character vector or a string scalar. Valid values are `"X"`, `"Y"`, or `"X + Y"`.

Default: `"X + Y"`

• `Enable` –– Set this property to `true` to enable peak finder measurements. Valid values are `true` or `false`.

Default: `false`

All `PeakFinderSpecification` properties are tunable.

Tunable: Yes

Scope Window Use

Open the Peak Finder pane () and modify the Settings options.

Enable cursor measurements to display screen or waveform cursors. The `CursorMeasurements` property uses the `CursorMeasurementsSpecification` properties.

The `CursorMeasurementsSpecification` properties are:

• `Type` –– Type of the display cursors, specified as either `"Screen cursors"` or ```"Waveform cursors"```.

Default: `"Waveform cursors"`

• `ShowHorizontal` –– Set this property to `true` to show the horizontal screen cursors. This property applies when you set the `Type` property to `"Screen cursors"`.

Default: `true`

• `ShowVertical` –– Set this property to `true` to show the vertical screen cursors. This property applies when you set the `Type` property to `"Screen cursors"`.

Default: `true`

• `Cursor1TraceSource` –– Specify the waveform cursor 1 source as a positive real scalar. This property applies when you set the `Type` property to `"Waveform cursors"`.

Default: `1`

• `Cursor2TraceSource` –– Specify the waveform cursor 2 source as a positive real scalar. This property applies when you set the `Type` property to `"Waveform cursors"`.

Default: `1`

• `LockSpacing` –– Lock spacing between cursors, specified as a logical scalar.

Default: `false`

• `SnapToData` –– Snap cursors to data, specified as a logical scalar.

Default: `true`

• `XLocation` –– x-coordinates of the cursors, specified as a real vector of length equal to 2.

Default: `[-2500 2500]`

• `YLocation` –– y-coordinates of the cursors, specified as a real vector of length equal to 2. This property applies when you set the `Type` property to `"Screen cursors"`.

Default: `[-55 5]`

• `Enable` –– Set this property to `true` to enable cursor measurements. Valid values are `true` or `false`.

Default: `false`

All `CursorMeasurementsSpecification` properties are tunable.

Scope Window Use

Open the Cursor Measurements pane () and modify the Settings options.

Enable channel measurements to compute and display the occupied bandwidth or adjacent channel power ratio. The `ChannelMeasurements` property uses the `ChannelMeasurementsSpecification` properties.

The `ChannelMeasurementsSpecification` properties are:

• `Algorithm` –– Type of measurement data to display, specified as either `"Occupied BW"` or `"ACPR"`.

Default: `"Occupied BW"`

• `FrequencySpan` –– Frequency span mode, specified as either `"Span and center frequency"` or ```"Start and stop frequencies"```

Default: `"Span and center frequency"`

• `Span` –– Frequency span over which the channel measurements are computed, specified as a real, positive scalar in Hz. This property applies when you set the `FrequencySpan` property to `"Span and center frequency"`.

Default: `2000` Hz

• `CenterFrequency` –– Center frequency of the span over which the channel measurements are computed, specified as a real scalar in Hz. This property applies when you set the `FrequencySpan` property to ```"Span and center frequency"```.

Default: `0` Hz

• `StartFrequency` –– Start frequency over which the channel measurements are computed, specified as a real scalar in Hz. This property applies when you set the `FrequencySpan` property to `"Start and stop frequencies"`.

Default: `-1000` Hz

• `StopFrequency` –– Stop frequency over which the channel measurements are computed, specified as a real scalar in Hz. This property applies when you set the `FrequencySpan` property to `"Start and stop frequencies"`.

Default: `1000` Hz

• `PercentOccupiedBW` –– Percent of power over which to compute the occupied bandwidth, specified as a positive real scalar. This property applies when you set the `Algorithm` property to `"Occupied BW"`.

Default: `99`

• `NumOffsets` –– Number of adjacent channel pairs, specified as a real, positive integer. This property applies when you set the `Algorithm` property to `"ACPR"`.

Default: `2`

• `AdjacentBW` –– Adjacent channel bandwidth, specified as a real, positive scalar. This property applies when you set the `Algorithm` property to `"ACPR"`.

Default: `1000`

• `FilterShape` –– Filter shape for both main and adjacent channels, specified as `"None"`, `"Gaussian"`, or `"RRC"`. This property applies when you set the `Algorithm` property to `"ACPR"`.

Default: `"None"`

• `FilterCoeff` –– Channel filter coefficient, specified as a real scalar between `0` and `1`. This property applies when you set the `Algorithm` property to `"ACPR"` and the `FilterShape` property to either `"Gaussian"` or `"RRC"`.

Default: `0.5`

• `ACPROffsets` –– Frequency of the adjacent channel relative to the center frequency of the main channel, specified as a real vector of length equal to the number of offset pairs specified in `NumOffsets`. This property applies when you set the `Algorithm` property to `"ACPR"`.

Default: `[2000 3500]`

• `Enable` –– Set this property to `true` to enable channel measurements. Valid values are `true` or `false`.

Default: `false`

All `ChannelMeasurementsSpecification` properties are tunable.

Scope Window Use

Open the Channel Measurements pane () and modify the Measurement and Channel Settings options.

Enable distortion measurements to compute and display the harmonic distortion and intermodulation distortion. The `DistortionMeasurements` property uses the `DistortionMeasurementsSpecification` properties.

The `DistortionMeasurementsSpecification` properties are:

• `Algorithm` –– Type of measurement data to display, specified as either `"Harmonic"` or `"Intermodulation"`.

Default: `"Harmonic"`

• `NumHarmonics` –– Number of harmonics to measure, specified as a real, positive integer. This property applies when you set the `Algorithm` to `"Harmonic"`.

Default: `6`

• `Enable` –– Set this property to `true` to enable distortion measurements.

Default: `false`

All `DistortionMeasurementsSpecification` properties are tunable.

Scope Window Use

Open the Distortion Measurements pane () and modify the Distortion and Harmonics options.

Enable CCDF measurements to display the probability of the input signal's instantaneous power being a certain amount of dB above the signal's average power. The `CCDFMeasurements` property uses the `CCDFMeasurementsSpecification` properties.

The `CCDFMeasurementsSpecification` properties are:

• `PlotGaussianReference` –– Set this property to `true` to plot a reference CCDF curve. The reference CCDF curve represents the power of a complex white Gaussian noise, calculated as a chi-squared distribution.

Default: `false`

• `Enable` –– Set this property to `true` to enable CCDF measurements. Valid values are `true` or `false`.

Default: `false`

All `CCDFMeasurementsSpecification` properties are tunable.

Scope Window Use

Open the CCDF Measurements pane () and enable the Plot Gaussian reference option.

Visualization

Title of the scope window.

Tunable: Yes

Data Types: `char` | `string`

Spectrum Analyzer window position in pixels, specified by the size and location of the scope window as a four-element double vector of the form [left bottom width height]. You can place the scope window in a specific position on your screen by modifying the values to this property.

By default, the window appears in the center of your screen with a width of `800` pixels and height of `450` pixels. The exact center coordinates depend on your screen resolution.

Tunable: Yes

Specify the type of plot to use for displaying normal traces as either `"Line"` or `"Stem"`. Normal traces are traces that display free-running spectral estimates.

Tunable: Yes

Dependencies

To enable this property, set:

• `ViewType` to `"Spectrum"` or `"Spectrum and spectrogram"`

• `PlotNormalTrace` to `true`

Scope Window Use

Open the Style properties and set Plot type.

Data Types: `char` | `string`

Set this property to `false` to remove the display of the normal traces. These traces display the free-running spectral estimates. Even when the traces are removed from the display, the Spectrum Analyzer continues its spectral computations.

Tunable: Yes

Dependency

To enable this property, set `ViewType` to `"Spectrum"` or ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, select Normal trace.

Data Types: `logical`

To compute and plot the maximum-hold spectrum of each input channel, set this property to `true`. The maximum-hold spectrum at each frequency bin is computed by keeping the maximum value of all the power spectrum estimates. When you toggle this property, the Spectrum Analyzer resets its maximum-hold computations.

Tunable: Yes

Dependency

To enable this property, set `ViewType` to `"Spectrum"` or ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, select Max-hold trace.

Data Types: `logical`

To compute and plot the minimum-hold spectrum of each input channel, set this property to `true`. The minimum-hold spectrum at each frequency bin is computed by keeping the minimum value of all the power spectrum estimates. When you toggle this property, the Spectrum Analyzer resets its minimum-hold computations.

Tunable: Yes

Dependency

To enable this property, set `ViewType` to `"Spectrum"` or ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Spectrum Settings. In the Trace options section, select Min-hold trace.

Data Types: `logical`

The simulation speed is faster when this property is set to `true`.

• `true` — the scope logs data for later use and updates the display at fixed intervals of time. Data occurring between these fixed intervals might not be plotted.

• `false` — the scope updates every time it computes the power spectrum. Use the `false` setting when you do not want to miss any spectral updates at the expense of slower simulation speed.

Data Types: `logical`

Specify the display title as a character vector or string.

Tunable: Yes

Scope Window Use

Open the Configuration Properties. Set Title.

Data Types: `char` | `string`

Specify the text for the scope to display to the left of the y-axis.

Regardless of this property, Spectrum Analyzer always displays power units as one of the `SpectrumUnits` values.

Tunable: Yes

Dependency

To enable this property, set `ViewType` to `"Spectrum"` or ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Configuration Properties. Set Y-label.

Data Types: `char` | `string`

To show a legend with the input names, set this property to `true`.

From the legend, you can control which signals are visible. This control is equivalent to changing the visibility in the Style dialog box. In the scope legend, click a signal name to hide the signal in the scope. To show the signal, click the signal name again. To show only one signal, right-click the signal name. To show all signals, press Esc.

Note

The legend only shows the first 20 signals. Any additional signals cannot be viewed or controlled from the legend.

Tunable: Yes

Scope Window Use

Open the Configuration Properties. On the Display tab, select Show legend.

Data Types: `logical`

Specify the input channel names as a cell array of character vectors. The names appear in the legend, Style dialog box, and Measurements panels. If you do not specify names, the channels are labeled as `Channel 1`, `Channel 2`, etc.

Tunable: Yes

Dependency

To see channel names, set `ShowLegend` to `true`.

Scope Window Use

On the legend, double-click the channel name.

Data Types: `char`

Set this property to `true` to show gridlines on the plot.

Tunable: Yes

Scope Window Use

Open the Configuration Properties. On the Display tab, set Show grid.

Data Types: `logical`

Specify the y-axis limits as a two-element numeric vector, `[ymin ymax]`.

Example: `scope.YLimits = [-10,20]`

Tunable: Yes

Dependencies

• To enable this property, set the `ViewType` property to `"Spectrum"` or ```"Spectrum and spectrogram"```.

• The units directly depend upon the `SpectrumUnits` property.

Scope Window Use

Open the Configuration Properties. Set Y-limits (maximum) and Y-limits (minimum).

Control the color limits of the spectrogram using a two-element numeric vector, `[colorMin colorMax]`.

Example: `scope.ColorLimits = [-10,20]`

Dependencies

• To enable this property, set the `ViewType` property to `"Spectrogram"` or ```"Spectrum and spectrogram"```.

• The units directly depend upon the `SpectrumUnits` property.

Scope Window Use

Open the Configuration Properties. Set Color-limits (minimum) and Color-limits (maximum).

Specify when the scope automatically scales the axes. Valid values are:

• `"Auto"` — The scope scales the axes as-needed to fit the data, both during and after simulation.

• `"Manual"` — The scope does not scale the axes automatically.

• `"OnceAtStop"` — The scope scales the axes when the simulation stops.

• `"Updates"` — The scope scales the axes once after 10 updates.

Scope Window Use

Select Tools > Axes Scaling.

Data Types: `char` | `string`

Set this property to delay auto scaling the y-axis.

Dependency

To enable this property, set `AxesScaling` to `"Updates"`.

Scope Window Use

Open the Axes Scaling dialog box and set Number of updates.

Data Types: `char` | `string`

Specify the layout type as `"Horizontal"` or `"Vertical"`. A vertical layout stacks the spectrum above the spectrogram. A horizontal layout puts the two views side-by-side.

Tunable: Yes

Dependency

To enable this property, set `ViewType` to ```"Spectrum and spectrogram"```.

Scope Window Use

Open the Spectrum Settings. Set Axes layout.

Data Types: `char` | `string`

Set this property to `true` to open the scope when the simulation starts. Set this property to `false` to prevent the scope from opening at the start of simulation.

Scope Window Use

Select File > Open at Start of Simulation.

Data Types: `logical`

Set this property to `true` to show the spectrum analyzer window, or `false` to hide the spectrum analyzer window.

Examples

collapse all

Create a new Simulink® model with a randomly-generated name.

```sysname=char(randi(26,1,7)+96); new_system(sysname);```

Add a new Spectrum Analyzer block to the model.

`add_block('built-in/SpectrumAnalyzer',[sysname,'/SpectrumAnalyzer'])`

Call the `get_param` function to retrieve the default Spectrum Analyzer block configuration properties.

`config = get_param([sysname,'/SpectrumAnalyzer'],'ScopeConfiguration')`
```config = SpectrumAnalyzerConfiguration with properties: NumInputPorts: '1' InputDomain: 'Time' SpectrumType: 'Power' ViewType: 'Spectrum' SampleRateSource: 'Inherited' Method: 'Welch' PlotAsTwoSidedSpectrum: 1 FrequencyScale: 'Linear' Advanced FrequencySpan: 'Full' FrequencyResolutionMethod: 'RBW' RBWSource: 'Auto' OverlapPercent: '0' Window: 'Hann' SpectrumUnits: 'dBm' AveragingMethod: 'Running' SpectralAverages: '1' ReferenceLoad: '1' FrequencyOffset: '0' TreatMby1SignalsAsOneChannel: 1 Spectrogram No properties. Measurements MeasurementChannel: '1' SpectralMask: [1x1 dsp.scopes.SpectralMaskSpecification] PeakFinder: [1x1 dsp.scopes.PeakFinderSpecification] CursorMeasurements: [1x1 dsp.scopes.CursorMeasurementsSpecification] ChannelMeasurements: [1x1 dsp.scopes.ChannelMeasurementsSpecification] DistortionMeasurements: [1x1 dsp.scopes.DistortionMeasurementsSpecification] CCDFMeasurements: [1x1 dsp.scopes.CCDFMeasurementsSpecification] Visualization Name: 'SpectrumAnalyzer' Position: [240 287 800 450] PlotType: 'Line' PlotNormalTrace: 1 PlotMaxHoldTrace: 0 PlotMinHoldTrace: 0 ReducePlotRate: 1 Title: '' YLabel: '' ShowLegend: 0 ChannelNames: {''} ShowGrid: 1 YLimits: [-80 20] AxesScaling: 'Auto' OpenAtSimulationStart: 1 Visible: 0 ```

Compute and display the power spectrum of a noisy sinusoidal input signal using the Spectrum Analyzer block. Measure the peaks, cursor placements, adjacent channel power ratio, distortion, and CCDF values in the spectrum by enabling these block configuration properties:

• PeakFinder

• CursorMeasurements

• ChannelMeasurements

• DistortionMeasurements

• CCDFMeasurements

Open and Inspect the Model

Filter a streaming noisy sinusoidal input signal using a Lowpass Filter block. The input signal consists of two sinusoidal tones: 1 kHz and 15 kHz. The noise is white Gaussian noise with zero mean and a variance of 0.05. The sampling frequency is 44.1 kHz. Open the model and inspect the various block settings.

```model = 'spectrumanalyzer_measurements.slx'; open_system(model) ```

Access the configuration properties of the Spectrum Analyzer block using the `get_param` function.

```sablock = 'spectrumanalyzer_measurements/Spectrum Analyzer'; cfg = get_param(sablock,'ScopeConfiguration'); ```

Enable Measurements Data

To obtain the measurements, set the `Enable` property of the measurements to `true`.

```cfg.CursorMeasurements.Enable = true; cfg.ChannelMeasurements.Enable = true; cfg.PeakFinder.Enable = true; cfg.DistortionMeasurements.Enable = true; ```

Simulate the Model

Run the model. The Spectrum Analyzer block compares the original spectrum with the filtered spectrum.

```sim(model) ```

The right side of the spectrum analyzer shows the enabled measurement panes.

Using `getMeasurementsData`

Use the `getMeasurementsData` function to obtain these measurements programmatically.

```data = getMeasurementsData(cfg) ```
```data = 1x5 table SimulationTime PeakFinder CursorMeasurements ChannelMeasurements DistortionMeasurements ______________ __________ __________________ ___________________ ______________________ {[0.9985]} 1x1 struct 1x1 struct 1x1 struct 1x1 struct ```

The values shown in measurement panes match the values shown in `data`. You can access the individual fields of `data` to obtain the various measurements programmatically.

Compare Peak Values

As an example, compare the peak values. Verify that the peak values obtained by `data.PeakFinder` match with the values seen in the `Spectrum Analyzer` window.

```peakvalues = data.PeakFinder.Value frequencieskHz = data.PeakFinder.Frequency/1000 ```
```peakvalues = 26.9068 26.3821 -3.5026 frequencieskHz = 15.0015 1.0049 13.3075 ```

Save and Close the Model

```save_system(model); close_system(model); ```

Version History

Introduced in R2013a