Contents

Servo Control with the Speedgoat IO301 FPGA Board

This example shows a workflow that uses HDL Coder™ to deploy a Simulink® subsystem to a Speedgoat FPGA I/O board installed in the target computer. A Simulink Real-Time™ application runs on the target computer and communicates with the FPGA over the PCI bus.

In this case, the FPGA algorithm performs three functions

  • PWM generation - useful for analog servo control

  • Increments a counter every 1 second

  • Maps pulses to 4 I/O channels - useful for sequencing LEDs on/off

The FPGA clock rate is 33MHz. The Simulink Real-Time simulation is set to 1KHz.

Open the FPGA Domain Model

Click here to open the FPGA model: dxpcSGIO301servo_fpgadxpcSGIO301servo_fpga.

This model contains the algorithm (green subsystem) that will eventually run on the FPGA. Also, it contains some test blocks to verify, in simulation, the algorithm is working as expected before synthesizing the FPGA bitstream. Note that this model is an "FPGA domain" model, meaning the simulation sample rate is representative of the clock rate of the FPGA (33MHz). Hence, 1 second of simulation requires 33e6 iterations of the model.

A test run of the model in Simulink is provided:

Scope1: PWM generation and hardware counter (first increment at 33e6 = 1 sec)

Scope2: Pulse trains used to sequence on/off 4 LEDs

Once the algorithm is ready, use the HDL Workflow Advisor to:

  • Select the FPGA I/O board

  • Map the subsystem inports and outports

  • Synthesize the FPGA bitstream

  • Generate the Simulink Real-Time interface subsystem

Using the HDL Workflow Advisor

To invoke the HDL Workflow Advisor, right-click the "ServoSystem" subsystem and select HDL Code -> HDL Workflow Advisor.

Task 1.1. Set Target Device and Synthesis Tool

Select Simulink Real-Time Turnkey by setting the target workflow to Simulink Real-Time FPGA I/O. Select the IO301 by setting the target platform to Speedgoat IO301. This will automatically configure the board characteristics and synthesis tool used in subsequent tasks.

When done, click Run This Task and continue with Task 1.2.

Task 1.2. Set Target Interface

Use the Target Platform Interface Table to specify and map the inports and outports. For this example:

  • Motor Cmd is the servo position command

  • LED1 Cmd is the LED1 On/Off command received from the target computer

  • LED2 Cmd is the LED2 On/Off command received from the target computer

  • LED3 Cmd is the LED3 On/Off pattern received from the target computer

  • LED4 Cmd is the LED4 On/Off pattern received from the target computer

  • PWM Signal is the PWM command to the servo using TTL I/O channel 37

  • Servo Cmd is the scaled servo position command

  • HW Counter is the counter that increments 1 count per second

  • LED1 is the command to LED1 using TTL I/O channel 32

  • LED2 is the command to LED2 using TTL I/O channel 33

  • LED3 is the command to LED3 using TTL I/O channel 34

  • LED4 is the command to LED4 using TTL I/O channel 35

When done, click Run This Task and continue with Task 5.2.

Task 5.2. Generate Simulink Real-Time Interface

Right-click Task 5.2 and click Run to Selected Task. The HDL Workflow Advisor runs all tasks, synthesizes the FPGA bitstream, and generates a new model that contains an Simulink Real-Time interface subsystem.

Upon completion, a newly generated model containing the Simulink Real-Time interface subsystem appears. On the surface, this subsystem looks like the FPGA subsystem. However, inside, the Simulink algorithm has been removed and replaced with blocks that the target application will use to communicate with the FPGA during simulation execution.

Open the Simulink Real-Time Model

Create or open an Simulink Real-Time model that will run on the target computer while the bitstream algorithm runs on the FPGA.

Click here to open the Simulink Real-Time model: dxpcSGIO301servo_xpcdxpcSGIO301servo_xpc.

Add the Simulink Real-Time Interface Subsystem

From the generated model, copy the Simulink Real-Time interface subsystem and paste it in the Simulink Real-Time model. Connect inports and outports. Double-click the interface subsystem and set mask parameters as required.

Click here to open the Simulink Real-Time model with the interface subsystem included: dxpcSGIO301servo_xpc_wissdxpcSGIO301servo_xpc_wiss.

Test the Model

Build the model. Upon build completion, the Simulink Real-Time application is downloaded to the target computer and the bitstream is downloaded to the FPGA.

Run the application. The servo position command, hardware counter, and LED On/Off patterns are displayed on the target scope.

% EOF dxpcSGIO301servoDemo.m
Was this topic helpful?